### PLC Programming and Electrical Safety#### Question 14:Which of the following statements about the basic rules to be followed when converting a ladder diagram into a logic diagram that can be loaded into the PLC is FALSE?- a. Each line of logic must end with a coil.- b. Only one set of contacts can be assigned to any input.- c. Any coil assigned to the same number as an output will control that output.- d. Each relay can have an infinite number of contacts.#### Question 15:In the figure below showing an explosionproof installation, the arrows point to the _______.(Graphical representation described)The diagram shows a setup with multiple components connected through wiring. At certain points in the diagram, arrows are pointing to specific parts that need to be identified.Options:- a. breakers- b. seals- c. fuses- d. controllers#### Question 16:Which of the following is NOT a recommended general procedure for dealing with harmonics?- a. Increase the 60-hertz part of the neutral current.- b. Pull extra neutral conductors.- c. Derate the amount of load on the transformer.- d. Add harmonic filters at the load.**Detailed Description of Diagram for Question 15:**The diagram illustrates an explosionproof installation which is typically used in hazardous environments to prevent ignitions and explosions. It consists of various components such as a motor, wiring conduits, and boxes. The arrows highlight critical points in the system which are essential for ensuring safety. The choices indicate elements that are integral to maintaining a safe and reliable electrical system in such environments.

Note: We are authorized to answer one question at a time, since you have not mentioned which…

14. which of the following statements about the basic rules to be followed when converting a ladder diagram into a logic diagram that can be loaded into the PLC is FALSE? Each line of logic must end with a coil. Only one set of contacts can be assigned to any input. Any coil assigned to the same number as an output will control that output. Each relay can have an infinite number of contacts. a. b. С. d.

14. which of the following statements about the basic rules to be followed when converting a ladder diagram into a logic diagram that can be loaded into the PLC is FALSE? Each line of logic must end with a coil. Only one set of contacts can be assigned to any input. Any coil assigned to the same number as an output will control that output. Each relay can have an infinite number of contacts. a. b. С. d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The symbol used for output device in PLC is Оа. Ob. C. O d.
A motor can be turned on when a momentarily pushbutton A or B is pressed.Another pushbutton C is used to turn off the motor. The motor is equipped withoverload relay. With the implementation of holding mechanism (SETRESET/KEEP), design a PLC program ladder diagram for this system
12
7777777777777
Dc motor control using L298N module. Write the code to drive a dc motor using L298N module in arduino IDE.
The solid state devices designed to perform logical decision making to control the equipment is a. Switches O b. Programmable Logic Controller O. Relays The symbol used for output device in PLC is а. Ob. HE O d.
Define in short about PLC.
21.a. What type of circuits are present on an axis logic card for a stepper motor system and are used toaccelerate and decelerate a motor?A. Timing circuitsB. Main oscillator circuitsC. Ramp circuitsD. Bias circuits21.b. A scaling or header plug is used on some brushless motor drive systems toA. connect the tachometer to the drive.B. divide the output pulse train.C. connect the front panel indicator lights to the drive.D. set the current limit of the drive.
5. Name PLC systems with are using in Kazakhstan industry
Q4 (a) Draw symbols that are used in ladder diagram for relay, motor, switch and light. (b) Design a basic structure of a programmab le logic controller (PLC) system.
Which answer is correct?
1.Modular structure of PLC. The controller cycle. Please answer for this theoritical question