14. Suppose rod AB is hinged to a fixed wall. Rope CDE is attached to the rod at C, 4in from the hinge. The rope passes over a pulley D, which is mounted on another fixed wall. The angle ACD is 60 . Hand force is applied at point B, 5 in from the hinge. What the value of hand force and reaction force will be developed in hinge A* E T=50 b A 60° C 4' 5' Force ? 5 lb, 3.5 lb, 10 lb O 6.7 Ib, 35.6 lb, 25 lb 34.6 lb, 25 lb, 8.7 Ib 30.5 lb, 16.6 Ib, 25 lb

14. Suppose rod AB is hinged to a fixed wall. Rope CDE is attached to the rod at C, 4in from the hinge. The rope passes over a pulley D, which is mounted on another fixed wall. The angle ACD is 60 . Hand force is applied at point B, 5 in from the hinge. What the value of hand force and reaction force will be developed in hinge A* E T=50 b A 60° C 4' 5' Force ? 5 lb, 3.5 lb, 10 lb O 6.7 Ib, 35.6 lb, 25 lb 34.6 lb, 25 lb, 8.7 Ib 30.5 lb, 16.6 Ib, 25 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

- For the spring system given in Figure 1, Create the element matrices as well as the global stiffness and force matrix, note that k=1. Figure 1
Figure 1 below shows the bronze and galvani pipes are fastened to rigid supports at ends A and B and to a rigid plate C at their junction. The bronze pipe is twice as long as the galvani pipe. Two equal and symmetrically placed loads P act on the plate at C 1)Write one equilibrium equation involving reaction forces of the pipes with the help of free body diagram.[Note: Show all the forces acting on the members.] 2)Derive equilibrium equations for internal forces for section AC and BC with the help of respective free body diagrams.[Note: Show all the forces acting on the members.]
Figure B b 30° 2b 30° Н. 4 of 4 Correct Note that the internal reactions at B are not included in the free-body diagram of the subsystem ABC. Part D-A tractor shovel The tractor shovel shown (Figure 4) carries a 535 kg load that has its center of mass at H. The shovel's dimensions are: a = 50.0 mm, b = 200 mm, c = 300 d = 100 mm, and e = 350 mm. Find the reaction force at E. Assume that the positive direction of the x and y axes is to the right and upward, respectively. Enter the Cartesian components of the reaction force at E separated by a comma. Express your answers in newtons to three significant figures. ► View Available Hint(s) ET, Ey = Submit VE ΑΣΦ ↓↑ vec ? N
Figure Q5a shows a truss structure in static equilibrium that is simply supported at A and C. Calculate the reaction forces RA and RC when subjected to vertical loads of 50 kN, 25 kN and 15 kN at nodes D, E & C, respectively.
For the statically indeterminate frame shown in Figure 2, use the moment distribution methodto determine the moments at each joint and support. The members are fixed connected at the supports and joints. EI is the same for each member. Suppose that w = 18 kN/m, P1 = 3x kN,and P2 = 22.x kN. Then draw the SFD and BMD. x=9
O16 ll zain IQ Capture.PNG → PROBLEM-6 (HW)The system consisting of the bar O.1, two identical pulleys, and a section of thin tape is subjected to the two 1SO-N tensile forces shown in the figure. Determine the equivalent force-couple system at point O. 180 N r= 25 mm 100 mm 180 N 45 50 mm 29 ...
A simple structure is to be built to hold load at C as shown in Figure Q5. Body ABC is pin joint at wall A is regarded as a rigid body and is pin supported to rod BD at B. The respective dimensions are as shown in the figure. A support unit is to be connected by pin between point B and point D or point D' at the wall. a) Compare and analyze the two positions for the support unit not to fail by buckling when maximum load F is applied at C. Which position is the better choice between D and D' ? b) If load F is in opposite direction, what is the maximum load F that can be applied. (Properties of rod BD, E= 200GPA, G=77 GPa, v=0.3, o, = 250 MPa ) A 1.6m В 1.4m C 0.9m F 10mm 4mm D 0.8m 9. 15mm mm D' Crossection of Hollow Rod BD or BD'. ( 10mm x 15mm and 4mm x 9mm) Figure 05
The frame in (Figure 1) supports the 350lb load. The pulley at C has a radius of 0.5 ft. The pulley at D has a radius of 0.25 ft. a) Determine the reaction at pin A. b) Determine the reaction at pin B.
answer all parts
Q/ For the mechanism shown below, compute the magnitude of the force (F) required to break contact at point (c)? C 3 m s = 10 mm K = 1800 N/m wwwro Q 3 m 4 m 4 m F
2D truss system below has 5 elements and 4 joints. The truss system is roller supported at joint 1 and pin supported at joint 3. Calculate all member forces of the truss system using the method of joints! Discuss your results! Assume a = 20 ft and P = 8 kips. Perform your calculations on a blank paper using the Given, Find, Analyze layout and draw free-body diagram to describe 2D systems