14. An 8 pole 50 Hz, three phase induction motor runs at a speed of 720 rpm when delivering full load torque. Its stand still rotor resistance and reactance are 0.1 ohm and 0.6 ohm per phase respectively. An additional resistance of 0.5 ohm per phase is inserted in the rotor circuit to control the speed. Calculate the speed at which the motor runs now with full load torque remaining the same. (Ans: 570 rpm)

14. An 8 pole 50 Hz, three phase induction motor runs at a speed of 720 rpm when delivering full load torque. Its stand still rotor resistance and reactance are 0.1 ohm and 0.6 ohm per phase respectively. An additional resistance of 0.5 ohm per phase is inserted in the rotor circuit to control the speed. Calculate the speed at which the motor runs now with full load torque remaining the same. (Ans: 570 rpm)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

d) A 2-pole induction motor is fed with a 230 V, 50 Hz supply and is running at no load. i. Calculate its angular speed in rpm. ii. Explain how can we slow down the speed of the motor above, at no load? iii. Explain what will happen to the speed of the motor if we slowly add amechanical load to the motor.
Q2 Complete the answer : The rotor reactance of the three phase induction motor is varies with ................... of the rotor current.
The rotor of the 4-pole three-phase squirrel cage induction motor has been replaced with the rotor of the three-phase 4-pole rotor wound induction motor. When the motor is fed with normal supply, the machine will a) Does not work b) Runs at a very slow pace c) Runs at slightly lower speed than normal speed d) Runs at a slightly higher speed than normal speed e) none
what are the disadvantages of slip ring induction motor?
12. The IR-compensation in frequency control of induction motors is used for: a) compensation of the voltage drop in the active resistance of the stator winding. b) compensation of the voltage drop in the inductive reactance of the stator winding. c) keeping the motor voltage constant. d) keeping the motor speed constant U₁ U₁ Us0 0 f. f₁
Answer it right..
A three-phase induction motor used for a commercial application in Oman 50HZ runs at 584 rpm at no load and at 546 rpm at full load. a) How many poles do this motor have? b) What is the percentage slip at full load? c) The frequency of the rotor currents when slip is 7 % d) The frequency of the rotor currents at standstill.
Q5) discuss two only : a) the frequeney of an alternator. b)what is the disadvantages of split phase induction motor. c) discuss the armature and shunt torque of the DC motor.
Find the value:
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.
A 3 phase, 1500 rpm, 2200 V, star connected synchronous motor has an impedance of 0.4+j90 per phase. At some excitation 2900 V is induced in the armature. Find the maximum torque developed by motor before the motor breaks out of synchronism. Also find the load angle this time.