14 Which type of Insulator is used in Substations to support connections for High Voltage Switchgears, Current Transformers, and etc.? A. SUSPENSION TYPE B. PIN TYPE C. POST TYPE D. STRAIN TYPE

Q: What code sets standards for electrical installation and related works?

A: In this case, the code that sets standard for the electrical installation and related works is to be…

Q: 1. Which of the following meters has a non-linear scale? a. Thermocouple meter b. Moving iron meter…

A: (1)  The potential produced by a thermocouple is proportional to temperature difference between two…

Q: What is the smallest square box that will accommodate four No. 12 conductors and four No. 10…

A: Given Required box size: Square conductors in box are are 4 number of 12 AWG conductors and 4 number…

Q: Larger conductors should be used for long runs to minimize the? A. Current B. Voltage drop c.…

A: for the long runs the larger conductors are generally used.

Q: Which among these statements is false or incorrect? A. The bigger the value of the Breaking Stress,…

A: The sag for a conductor is calculated by the formula  Sag=wl28TT=Tensile strengthsafety factor And…

Q: When installing grounding electrode conductor at services, it's common to use a single large common…

A: Here we discuss about grounding/earthing related concept.

Q: 70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit…

A: While calculating the conductor size for a continuous load, take 125% of overloading conditions…

Q: Multiple Choice. Refers to a point in a circuit where three or more wires are connected. A.…

A:

Q: a method of joining  two conductors usually applied in power circuits in household premises A.…

A: The method of joining two conductors usually applied in power circuit generally known as splices.

Q: How do voids in the insulation cause breakdown of the cable?

A: For the transmission and distribution purpose of electric power, high voltage cables are used. The…

Q: 9. What is the minimum ampacity of the wire that can be used for a 30A branch circuit?      a. 30A…

A:

Q: Question: How do the secondary voltage and current react to the different types of load and how do…

A: It is asked how in transformer the secondary voltage and current react to the different types of…

Q: Coaxial cable insulator is made up of a. Aluminium Foil b. Teflon c. Braided Sheild d. Copper

A: In this question, choose the correct option Coaxial cable insulator is made up of...

Q: 8. The effect of high-frequency discharges on current transformers used in high-voltage circuits is…

A: The correct answer is A. porcelain insulator bushing. Current transformers (CTs) are used to measure…

Q: 5 a) Discuss Electricity power generation and distribution to residential properties b) with…

A: Explain the electricity power generation, Distribution board, some materials and accessories.

Q: Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters…

A: c) 50-195

Q: 4. Plastics are commonly used for (insulating). O Cover O Sheathing O Observe 5. The core is…

A: 1) to protect the flow of electricity outside the cable then we insulate and sheating the cable…

Q: 6. Which one of the following types of construction is used for potential transformers A.…

A: The correct answer is A. Window-type. Window-type construction is the most common type of…

Q: Blocks in power supply system does NOT include A.Regulator B.Solar panel C.Transformer…

A:

Q: Identify the installation symbol O Two Two way One gang switch O Two way Two gang switch O One way…

A: consider the given question;

Q: h.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: 3. The zero sequence current is times the current in neutral wire.

A: Zero sequence current in all phase are in phase and same magnitude . Neutral current sum of three…

Q: What is the electrical-resistance strain gage?

A: The electrical resistance strain gage is as follows: - Electrical resistance strain gages are…

Q: Low-voltage conductors. a. are not powerful enough to cause death from electrocution b. must exceed…

A: According to the question, we need to select the correct option Low-voltage conductors,  a. are not…

Q: We would like to run the power wires for both cooling pumps in the same RMC from the Breaker panel…

A: Option A (#6 AWG) is not large enough to handle a 100 amp load at 120/240V, as it is only rated for…

Q: Consider the circuit shown in Figure 6. SW1 is a "single pole single throw" (SPST) switch. (+1 R1…

A: given a circuit and asked find the voltage at A.

Q: Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a…

A: Dear student, *Keeping a note ?as per our company guidelines we are supposed to answer ?️only first…

Q: EASE HELP ME CHOOSE WHAT CORRECT LETTER OR ANSWER 1. The direction of induced voltage in a conductor…

A: 1). The direction of induced voltage depends only on field direction ( current direction). So…

Q: Question 7: 1- List the pins on Arduino that can do analog write. 2- In a PWM, given that the duty…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Methods of Wiring

Electrical wiring is the way of integrating cables and wires to interconnected equipment such as fuses, switches, sockets, lights, fans, and so on to the main distribution board, which is a specific structure attached to the utility pole that ensures a constant power supply.