14- The anchor shackle supports a cable force of 5.0 kN. If the pin has a diameter of 6 mm, determine the average shear stress in the pin.

Q: Find the value of a. TO a. Vs +3

A:

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: Q) Find Xc and Ye angle 10 m 20m 25 m

A: The Center of mass is a point where the sum of the moment of the weight of each particle is zero. It…

Q: A water tank consists of a cylinder section enclosed by hemispherical shell with the thickness of 15…

A:

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: 4. The top of a male dovetail is 4 inches wide. If the angle is 55° and the depth is 5/8 inch, what…

A: 4.88''Explanation:Let's illustrate the problem,Given the width of the top of male dovetail which is…

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: Find the measure of the angle (in degrees) made by the resultant of the concurrent forces with…

A:

Q: Find the volume of the given figure. 3ž in. 3 in. 1; in. radius 2 in. radius 7 in. y 2 in 3/4 1/2

A: It is required to determine volume of given section

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: 9. Find the volume of a hollow sphere if it's inside diameter is 1 inch and the outside diameter 5…

A: The volume of a hollow sphere can be obtained using the formula,

Q: A torque of 11519 inch-pounds is applied to a 1 ¾ inch diameter steel shaft. Use modulus of…

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: P4-2) Answer questions about the following drawing. a) How many linear dimensions? b) How many…

A: As we are entitled to solve upto three subpart. I am solving here the first three parts for You. To…

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: True

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Using just a yardstick or a measuring tape, open the classroom door 35 degrees. You cannot use a…

A:

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: A cube has an edge length of 7 cm. If it is divided up into 1-cm cubes, how many 1-cm cubes are…

A: Given   Base cube edge 7 cm Segregated cube edge 1 cm To find How many cubes are their

Q: A scientist dose a chemical substance in the test tube having a 10 mm diameter and generating a…

A: Given d=10mm=0.01mh=4.44cm=0.0444mm=10mg=10×10-6 kg

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body