14-23 The wood beam k subjected to a load of 12 kN II grais of wood in the heam at point A make an angle of 25 with the hortzontal as shown, determine the normal and shear stress that act perpendicular to the grains due to the laading, 12N Imim 200 mm

Q: 15 kip 15 kip 4 in. 4 in. 4 in. The beam has the cross section shown. Determine (a) the maximum…

A:

Q: F11-2. Determine the minimum diameter d to the nearest in. of the rod to safely support the load.…

A:

Q: 13-49. The sold rod s sabjectad to the kading shown. Determine the state of stress at point C, and…

A: Apply equilibrium force conditions along the all directions: Where, FX is the force components…

Q: The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It…

A:

Q: 14-35. Determine the maximum in-plane shcar stress developed at point A on the cross section of the…

A: Draw the free body diagram: Calculate the reactions using static equilibrium conditions: Consider…

Q: 14-12. Determine the oquivalent state of stress on an clement at the same point oriented 6r…

A: Given Data: The value of σx=150 MPa. The value of σy=100 MPa. The value of τxy=75 MPa. The value of…

Q: 9-30. Determine the principal stresses in the beam at point A. 150 kN m\M 021 MICH 60 kN 50 mm -0.5…

A:

Q: Given the state of stress shown on the element, find savg and tmax in@planeand show the results on a…

A: Given, σy=-4 MPaσx=+4 MPa   Average normal stress:σavg = σx-σy2σavg = -4-42σavg =-4 MPa

Q: Crven Assembly consist of a sibel ( Es = 200 Gpd As = 1500 mm ² ) Kod AB and a brass ( GPa EB²=100 e…

A:

Q: 14-24. The Intermal loadings at a sectilon of the beam are shown. Determine the in-plane principal…

A: Given: The moment about z-axis, Mz = 10 kNm The moment about y-axis, My = 500 Nm The normal force, P…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The rod below is subjected to the loadings shown. Calculate the state of stress at points A and C.…

A: Hi, As per the guidelines we cannot provide a handwritten solution. We can only provide a typed…

Q: FI5-1. Determine the minimum dimensicon a to the nearest mm of the beam's cross section to safely…

A: Given: The maximum allowable normal stress, σall = 10 MPa The maximum allowable shear stress, τall =…

Q: R14-3. Determine the equivalent state of stress if an element is oriented 40° clockwise from the…

A:

Q: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam.…

A: Given: Moment area of inertia of the beam about horizontal neutral axis: →INA=0.225×10-3…

Q: 14-16. Determine the oquivalent state of stress on an clement at the point which represents (a) the…

A: Given Data: The value of σx=50 MPa. The value of σy=0 The value of τxy=15 MPa. Part (a): The value…

Q: 14-33 Determine the principal stresses in the cantilevered beam at points A and . 31 12 1200 mm 150…

A: forces and moments are shown in figure below

Q: 14-69. Determine the principal stress at point A on the cross section of the hanger at section b-b.…

A: Consider the Free body diagram of the system at b-b section.

Q: The steel bracket is used to connect the ends of two cables Part A O max If the applied force P= 1…

A: Given that,Applied force = P = 1 kipDiameter of rod of bracket = d = 2.25 inTo find:The maximum…

Q: The principal stress o2 is -50ksi A c ksi T B 25ksi 10 ksi

A: To find: The principle stress σ2. Given: Consider the figure below:

Q: Determine the maximum axial forc e P that can be applied to the bar. The bar is made from steel and…

A:

Q: 8-2. Determine the state of stress on an element at the same point oriented 30° clockwise with…

A:

Q: 14-29. The beam has a rectangular cros section and k subjected to the lkadings shown. Determine the…

A: load 1 acting on beam=20 kN ;load 2 acting on beam=10 kN ; M=moment from point A-B IXX=moment of…