13.5 through 13.8 Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs. P13.1- P13.4 by using the method of consistent deformations. Select the reaction moment at the fixed support to be the redundant. FIG. P13.3, P13.7 120 kN 75 kN - m C B 6 m 6 m El = constant

13.5 through 13.8 Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs. P13.1- P13.4 by using the method of consistent deformations. Select the reaction moment at the fixed support to be the redundant. FIG. P13.3, P13.7 120 kN 75 kN - m C B 6 m 6 m El = constant

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The aluminium (G= 27.1 GPa) hollow thin walled torsion member has shown dimensions in Fig. 2. Its length is 3 m. If the member is subjected to a torque of 11 kN-m, determine the maximum shear stress and angle of twist. 120 mm b -200 mm 5 mm -5 mm, 5 mm Fig. 2 80 mm 5 mm 5 mm
(b-8b)+ (d-8d) Fig. 1.5 L + ÖL 1.9.1. For One-Dimensional Stress System. The relationship between stress and strain for a unidirectional stress (i.e., for normal stress in one direction only) is given by Hooke's law, which states that when a material is loaded within its elastic limit, the normal stress developed is proportional to the strain produced. This means that the ratio of the normal Lateral strain Poisson's ratio, u = Longitudinal strain Lateral strain = u x Longitudinal strain Problem 1.5. The safe stress, for a hollow steel column which carries an axial load of 2.1 x 10³ kN is 125 MN/m². If the external diameter of the column is 30 cm, determine the internal diameter.
Prob. 2.9-10. At room temperature (70°F) and with no axial load (P = 0) the extensional strain of the prismatic bar (Fig. P2.9-10) in the axial direction is zero, that is, € = 0. Subsequently, the bar is heated to 120°F and a tensile load P is applied. The material properties for the bar are: E = 10 × 10³ ksi and a = 13 x 10-6/F, and the cross-sectional area of the bar is 1.8 in². For the latter load-temperature condi- tion, the extensional strain is found to be €x = 900 × 10 6. (a) Determine the value of the axial tensile load P. (b) De- termine the normal stress and the shear stress on the oblique plane NN'. (Note: The total strain is the sum of strain asso- ciated with normal stress o (Eq. 2.14) and the strain due to change of temperature AT (Eq. 2.8).) in. P Gage measures extensional strain Ex N N' 25° P2.9-10 X
How would you draw the deformation sketch?
Q-2 Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.2. (EI is constant). 20 KN 10 KN B 2 m D et 2 m Fig.2
Q1: Due to the applied loading, the element at point A on the solid shaft in Fig.a is subjected to the state of stresses shown in Fig. b. Determine the principal stresses and maximum shear stresses acting at this point. Draw the element at each state of stresses. P Fig. a T 45 MPa <-30 MPa Fig. b 10 MPA
6. In Fig. 6, a 1.5 m long cantilever beam with a circular cross section (R = 100 mm) and two symmetrically positioned longitudinal holes is loaded by a concentrated force P at its tip. The material is a titanium alloy with a 600 MPa maximum allowed working stress when bent. Find the maximum permitted vertical force P value. 1.5 m Radius= R = 100 mm Radius of hole =
Determine the distribution of the shear stress over the cross section of the beam shown in Fig.a
(b) A cooling tube having the cross section shown in Fig. Q1(b) is formed from a sheet of stainless steel of 3 mm thickness. The radii c₁ = 150 mm and c₂ = 100 mm are measured to the center line of the sheet metal. Knowing that a torque of magnitude T = 3 kNm is applied to the tube, determine (i) the maximum shearing stress in the tube (ii) the magnitude of the torque carried by the outer circular shell Neglect the dimension of the small opening where the outer and inner shells are connected. Hint: q - T 2A q=rt, T = Fr. Fig. Q1(b)
Q3) Determine the moment of the force about point O. show in Fig (3) Neglect the thickness of the member? 40 N 30 N J 100 mm 200 mm Figure (3) 50 N
574
An aluminum bar having a cross-sectional area of 160 square millimeters carries the axial loads at the positions shown in the figure. Assume that the bar is suitably braced to prevent buckling. E = 70 GPa. 35 KN 15 KN 30 KN 10 KN -> 0.8 m 1.0 m 0.6 m B FIGURE 9 Determine the deformation at segment AB Determine the deformation at segment BC. Determine the deformation at segment CD. Determine the total deformation of the bar.