13.2. The incremental fuel cost in S/MWh for four units of a plant are df2 0.0096P,2 + 6.0 df, 0.012 P + 9.0 dP dP,2 df, 0.008 P, + 8.0 dP, df. 0.0068 P+ 10.0 dP Assuming that all four units operate to meet the total plant load of 80 MW, find the incremental fuel cost A of the plant and the required output of each unit for economic dispatch.

13.2. The incremental fuel cost in S/MWh for four units of a plant are df2 0.0096P,2 + 6.0 df, 0.012 P + 9.0 dP dP,2 df, 0.008 P, + 8.0 dP, df. 0.0068 P+ 10.0 dP Assuming that all four units operate to meet the total plant load of 80 MW, find the incremental fuel cost A of the plant and the required output of each unit for economic dispatch.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In Chopper operation I0 is positive , the direction of power flow will be from ......... to .........
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MW? Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
Explain the concept of power factor correction and its impact on energy efficiency in an industrial setting.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. G3: 300 MVA rating, R3 = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW
(4) show the figure (if needed), given, formula and substitution. thank you! promise i'll rate.
In he giun airauit what resistor RL will absorb masimuon power and what is hir poscr! RL is cqual to (if your answrs are mot ahole numbers, round af to 2 deimal places.) ohms and Pmax is equal to wattr. 1SSL Tr2oN (0.2Vx
Two loads connected in parallel take a total of 2.4 kW with a lag fp of 0.8, from a line at 120 V rms and 60 Hz. of the loads absorbs 1.5kW with lagged fp of 0.707. Deter- mine: a) the fp of the second charge, b) the element in parallel required to correct the fp of the two charges and convert it to behind 0.9.
A high-voltage direct-current generating station delivers 5 MW of power at 178 kV to a city, as depicted in Figure below. The city is represented by resistance R₁ and each of the two wires of the transmission line between the generating station and the city is represented by resistance RTL. The distance between the two locations is 1752 km and the transmission lines are made of 7 cm diameter copper wire. Determine how much power is consumed by the transmission line. Please enter your answer 2 decimal places and in terms of Watt. (for copper-1.72 x 10-8) Vo Station RTL RTL ww RL (city)
What is the significance of power factor correction in power systems, and how is it achieved?