13. When steam expands through a nozzle from a pressure of 300psia to a final pressure of 5 psia and the initial and final enthalpy values are 1187 BTU/lb and 1051 BTU/lb, respectively, calculate the final velocity in m/min. Neglect inlet velocity, gravitational effects, and heat loss through the casing.

13. When steam expands through a nozzle from a pressure of 300psia to a final pressure of 5 psia and the initial and final enthalpy values are 1187 BTU/lb and 1051 BTU/lb, respectively, calculate the final velocity in m/min. Neglect inlet velocity, gravitational effects, and heat loss through the casing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Helium expands polytropically through a gas turbine according to the process PV1219 = C. If the turbine produces 25.6 MW, determine the heat transferred in kJ/s.
Steam enters the nozzle operating a steady state pressure of 2.5 MPa and a temperature of 300 °C ( H1 = 3008.8 kJ/kg) and leaves at a pressure of 1.7 MPa with a velocity of 470 m/s. The rate of flow of steam through the nozzle is 1360 kg/hr. Neglecting the inlet velocity of the steam and considering the flow in the nozzle is adiabatic, find:a. the exit enthalpy in kJ/kg, ( H2)b. the nozzle exit area ( in cm) if V exit is 0.132 m^3 /kg c. the system
8. In a steady flow apparatus 135 KJ of work is done by each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.30 m³/kg, 600 kPa, and 16m/s. The inlet is 32m above the floor and the discharge pipe are at floor level. The discharge conditions are 0.60 m³/kg, 1 bar, and 270 m/s. The total heat loss between the inlet and discharge is 9KJ/kg of fluid. In flowing through this apparatus, does the specific internal energy increase or decrease? And by how much?
3. A fluid system undergoes a non-flow frictionless process from 5.5 ft to a final volume 2.5 ft in accordance with the defining relation P= 60/V + 23 psi, where volume is in ft. During the process the system reject 30 BTU of heat. Determine the change in enthalpy and internal energy.
1
In Otto Cycle, air at 18oC is first compressed to one-ninth of its original volume. If the heat input to the cycle is 460 KJ/Kg of air, determine a. The temperature of the remaining points in the cycle. b. The ratio of the maximum and minimum pressure in the cycle.
The kinetic energy of air as it flows through an adiabatic nozzle. decreases increases remains constant
A mixing vessel initially contains 4,485.43 lb of liquid fluid. The vessel is fitted with two inlet pipes, one delivering hot fluid at a mass flow rate of 0.635 lb/sec and the other delivering cold fluid at a mass flow rate of 0.836 lb/sec. Fluid exits through a single pipe at a mass flowrate of 1.144 lb/sec. Calculate the amount of fluid, in lb, in the tank after 44 minutes.
Saturated steam at P1=25 bar expands adiabatically through a throttling valve to P2=4 bar. If the quality of the steam at the valve inlet is x1=0.9 what is the quality x2 at the valve outlet Please respond ASAP
9. Steam enters a turbine stage with an enthalpy of 3628 kJ/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kJ/kg and velocity of 124 m/s. Calculate the work done by the steam in kJ/kg.
2. In Otto Cycle, air at 18°C is first compressed to one-ninth of its original volume. If the heat input to the cycle is 460 KJ/Kg of air, determine a. The temperature of the remaining points in the cycle. b. The ratio of the maximum and minimum pressure in the cycle.