13. Estimate formation permeability and skin factor from the buildup test data given the following formation and fluid properties: q=1000 STB/D; tp=72 hr; pwf=3319.1 psia; h=12 ft; ø = 25.7%; rw=0.32 ft; B= 1.41 RB/STB; q= 12.5 × 10-6 psi-l; and u=0.53 %3D ср. BUILDUP TEST DATA FOR EXERCISE 2.13 Time Pressure Time Pressure Time Pressure (hours) (psi) (hours) (psi) (hours) (psi) 0.100 5155.7 0.993 5471.2 3.215 5626.1 0.220 5266.4 1.292 5506.3 3.958 5652.9 0.364 5335.5 1.650 5538.8 4.850 5678.7 0.537 5388.3 2.080 5569.3 5.920 5703.7 0.744 5432.4 2.596 5598.3 6.000 5705.4

13. Estimate formation permeability and skin factor from the buildup test data given the following formation and fluid properties: q=1000 STB/D; tp=72 hr; pwf=3319.1 psia; h=12 ft; ø = 25.7%; rw=0.32 ft; B= 1.41 RB/STB; q= 12.5 × 10-6 psi-l; and u=0.53 %3D ср. BUILDUP TEST DATA FOR EXERCISE 2.13 Time Pressure Time Pressure Time Pressure (hours) (psi) (hours) (psi) (hours) (psi) 0.100 5155.7 0.993 5471.2 3.215 5626.1 0.220 5266.4 1.292 5506.3 3.958 5652.9 0.364 5335.5 1.650 5538.8 4.850 5678.7 0.537 5388.3 2.080 5569.3 5.920 5703.7 0.744 5432.4 2.596 5598.3 6.000 5705.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 Two determinations for the plastic limit gave water contents of 22.8% and 23.2%. Determine (a) the liquid limit and plastic limit, (b) the plasticity index, (c) the liquidity index if the natural water content is 38% and (d) the void ratio at the liquid limit if G, = 2.7. (e) What is the soil state in the field? (f) Do you expect a brittle type of failure for this soil?
Calculate the quantity of the sand required (in cubic meter) in 20 cubic meters of reinforced cement concrete (1 : 2 : 4). (a) 2.87 mulos (b) 4.4 (c) 5.7 (d) 8.8
Urgent need the solution. Kindly answer everthing. Please skip if you're not going to answer them. Thank you.
Q24 Please provide justified answer asap
Data for Triaxial Test: Initial Length = Lo = 83mm. Initial Diameter = Do = 38mm. Cell Pressure = õ3 =128 kpa Deformation (AL) (mm) 0.1 0.3 Load (N) 30.97 0.6 1 61.94 89.65 118.9 1.2 128.77 1.4 140.18 1.5 146.7 1.6 148.33 1.7 144.71 1.8 143.44 1- Find the maximum shear stress that will be resisted by soil before failure? 2- Find the soil strength parameters (C, 0)? 3- Draw Mohr circle.
During Atterberg limit tessts in the Naboratory,the studens obtained the following results froma clayey soil. Wumber of Blows (N) Molsture Content \ 38/4 16 36/5 20 33.1 28 2/7 0 Plastic limit tests: Students conducted two trials and found that PL= 17 2% for the first trial and PL = 18.4% for the second trial. Assume that the liquid limit of the soil iS LL= 29.0% a. Determine the flow index. b. Determine the liquidity index of the soil if the in situ moisture content is 22.0%.
11.5 Following are the results of a laboratory consolidation test on a sample of undis- turbed clay obtained from the field. Pressure, o' (kg/cm?) Final helght of specimen (cm) 2.540 0.5 2.519 1.0 2.5 2.0 2.428 4.0 2.322 8.0 2.206 16.0 2.09 © Cengage laeming 2014
An oedometer test is conducted for a soil sample. The sample is consolidated under vertical stress of 50 kPa. The oedometer test finished at 144 min and data are given in table I. The average thickness of the sample is 20 mm. Predict the coefficient of consolidation (cv, in mm^2/min) using Casagrande log t method and Taylor square root of t method. Please use the empty graphical papers.
Ex Two identical soil samples (A) and (B) of a fully saturated N.C.C. were tested. Sample (A) was subjected to an unconfined compression test and failed when the deviator stress (OT-13) was (200) kN /n². Sample (B) was tested under UU conditions with a cell pressure of (300) kN/m². The pore water pressure at failure. was (200) kN/m². a) What was the pore water pressure at failure in sample (A). b) If C=o, Find (2) for this clay. (Itint. Start with soil B, and that (OJ) un= (FJ) afined). unconfined
A Cone Penetrometer Test (CPT) produces a continuous record of tip and sleeve resistance as well as pore pressure induced behind the cone tip. At a certain depth, the following are recorded: Cone Tip Resistance = 17 tsf; Friction Ration (Rf) = 2.6% The soil is most likely a O a Clayey Sit Ob Clay Sand Od Silt
Correct answer.