13) There is table in memory which has ten eight bit numbers starting at 9350H. write a program for 8085 to transfer the numbers from this table to another table that starts at location 9450H by swapping bit D6 and bit D2 if the number is greater than 90H else transfer by adding 48H.

Q: Assume that the stack address is Cs = 2 F30H, Ds: 2000H, SSA48AH Dees the adress Caver the segment…

A: Solution:

Q: 10) A sét of 10 current readings is stored in memory location starting at xx60H. write a program to…

A: Answer:  I have attached Assembly code and also I have given brief explanation.

Q: Select the component found on Microprocessor chip. Memory Registers Cache Memory Arithmetic Logic…

A: Microprocessor chip  are basically a silicon device that is acts as a CPU ( central processing unit)…

Q: Discuss the access levels required to perform the input and output operations using High-level…

A: High level language: It is a programming language. It enables a programmer to write programs that…

Q: Determines how fast instructions can be executed.

A: Execution of instructions Execution time is the total time a CPU spends computing on a given task.…

Q: What are the main functions of the CPU?

A: The central processing unit (CPU) of a computer is the hardware which performs the instructions of…

Q: Microprocessor is a/an electronic circuit that functions as the CPU of the computer

A: Please find the answer below :

Q: instruction only works with unsigned numbers. O a. CMP O b. SUB O c. DIV d. ADD

A: DIV instruction performs an unsigned division of the accumulator by the source operand. The dividend…

Q: Describe the components of a CPU (Central Processing Unit) and their functions in the execution of…

A: Cache memory is a high-speed, small-capacity volatile computer memory that stores frequently…

Q: List the main applications of 8 bit microprocessors?

A: 8-bit microprocessors are­ computing devices that can process 8 bits of data simultane­ously in a…

Q: Computers manipulate data and execute binary instructions. What use does binary serve?

A: Introduction: Computers are required for data manipulation and binary instruction execution. The…

Q: True or False Main memory is also known as RAM.

A: Memory: Computer memory is a physical device. Memory has used the store the data and instructions.…

Q: 4) Write a program to add all positive numbers stored in the memory location 4000H to 4000H. Display…

A: The answer is

Q: What addresses in memory contain array A?

A: Given: What addresses in memory contain array A?

Q: The number of general-purpose processors is one of the criteria used to categorize the different…

A: The solution is given in next step:

Q: 5) Write an assembly language program to calculate the average of ten numbers that are stored in…

A:

Q: Memory latency is(a) average down time (b) time to reference a block of data(c) processor access…

A: Given: Memory latency is(a) average down time (b) time to reference a block of data(c) processor…

Q: Question¹  Computer Science MICROPROCESSOR QUESTION Provide the command words for 8251, 8253, 8255…

A: Solution - The basic opertions and command word of given microprocessor 8251,8253,8255,8259 are…

Q: It's important to compare and contrast the uniprocessor and multiprocessor systems. Computers come…

A: the answer is given below:-

Q: Describe the technique via which a processor executes a program.

A: A processor, also known as a central processing unit (CPU), is a crucial component of a computer…

Q: Indicates that virtual machine instructions set architectures are not supported.

A: Introduction: The implementation of a virtual instruction set architecture (V-ISA) in a CPU using a…

Q: 1. The segment addresses are assigned as 0000H to F000H and the offset addresses values are from…

A: According to Bartleby Guidelines we need to answer only 3 sub questions so I have answered first…

Q: Explain the concept of a CPU in a computer system and its primary functions.

A: A Central Processing Unit (CPU) is the primary component of a computer system that is in charge of…

Q: Explain the contribution of early computers to the development of modern computers

A: Answer: The evolution of computing hardware can be traced from the earliest basic calculators to…

Q: An address in main memory is called

A: Answer the question presented by selecting the appropriate answer choice.

Q: Describe the process of data transfer between registers and memory using load and store…

A: The process of data transfer between registers and memory using load and store instructions is a…

Q: H.W: Draw a block diagram to implement the following statement: T: R2 R1 (LD) , R3 R3 +1 (INR)

A: Given statements  T: R2 <- R1 (LD)  R3<-R3+1(INR)

Q: How input and output operations take place in assembly language explain?

A: Lets see the solution to above question.

Q: 5. Draw a block diagram of maximum mode memory interface.

A: Maximum Mode Configuration of 8086: A processor is in the Maximum Mode Configuration of 8086 when…

Q: Briefly explain microcode interpreter

A: Microcode: All the operations which are performed by the processor are stored in the memory in the…

Q: Computer Machine Language please The machine language form of a jump instruction (j) is…

A: The answer is

Q: What characteristics influence the microprocessor's speed

A: Answer : There are some main characteristics that affect the microprocessor speed : 1) clock speed.…

Q: Write an assembly program that would behave as the following if statement: if (A > 10): X = 2 else…

A: Assembly code implemented in MIPS programming language is given below

Q: Data stored from 4040H to 4050H, transfer the data to other location in reverse order.

A: Here, I have to provide a solution for the above question.

Q: Discuss the basic program execution registers used in 64-bit mode.

A: Registers used in 64-bit mode: It contains 16 general purpose registers. Its default operand size is…

Q: This procedure counts the amount of CPU instructions required by each statement in the source code.

A: Introduction:   The process you're referring to is known as "profiling," and it's used to gauge how…