13/ Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 12 kg, 10 kg, 18 kg and 15 kg respectively and their radii of rotations are 40 mm, 50 mm, 60 mm and 30 mm. The angular position of the masses B, C and D are 60°, 135° and 270° from the mass A. Find the magnitude and position of the balancing mass at a radius of 100 mm.

13/ Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 12 kg, 10 kg, 18 kg and 15 kg respectively and their radii of rotations are 40 mm, 50 mm, 60 mm and 30 mm. The angular position of the masses B, C and D are 60°, 135° and 270° from the mass A. Find the magnitude and position of the balancing mass at a radius of 100 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Only question 4 , don't do others
The uniform rod of mass M and length L rotates in the plane of the figure about an axis through one end. As the rod swings through its lowest position, it collides with a putty wad of mass m, that sticks to the end of the rod. If the rod's angular speed just before collision is w, a) what is the angular speed of the rod-putty system immediately after collision? Rotation axis Rod b) What is the change in the kinetic energy of the rod-potty system (immediately before to immediately after the collision)? Does the kinetic energy increases, decreases, or remains the same? Provide your answers symbolically.
A wheel is attached by a cable to a block The wheel has a radius of 2ft and weighs 300lbs, the block weights 20lbs. If the radius of gyration about the point of rotation of the disk is 1.5ft, how many revolutions will it take for the wheel to come to a stop assuming it was moving at 10 rad/s CW. Assume the block is on the left side of the wheel and thus causes a CCW moment.
The force F 250 N is applied to a wheel weighing 20 kg and having a radius of inertia of 150 mm as shown in the figure. This force lifts a weight B of 10 kg. Calculate the angular acceleration of the pulley and the normal acceleration of the weight B, the tension of the rope and the reaction in the bearing of the pulley.
THE WEIGHT OF THE UNBALANCED WHEEL IS 200 KG AND IT HS A RADIUS OF GYRATION ABOUT ITS MASS CENTER, G, OF 0.3 METERS. AT THE INSTANT SHOWN IT IS ROTATING AT 6 RAD/SIN A CLOCKWISE DIRECTION. FIND THE FORCES BETWEEN AT THE PIVOT POINT C. Please include a Free Body Diagram
2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
The rod AB is non-uniform with a radius of gyration of 4.00 ft with respect to a horizontal axis through the center of mass G. It weighs 161 lb. At the moment shown the rod has a counterclockwise angular velocity of 3.00 rad/sec, and the spring is compressed by 2.00 ft. Calculate the force constant of the spring that will reduce the angular velocity of the rod to 1.50 rad/sec when it reaches the horizontal position. Assume the blocks A and B are weightless.
A shaft carries four masses A, B, C and D of magnitudes 18 kg, 15 kg, 27 kg, and 22.5 kg respectively and revolving at radii 20 mm, 25 mm, 30 mm and 15 mm respectively. The masses are rotating in the same plane. The angular position of masses B, C and D are 60 degrees , 135 degrees and 270 degrees from mass A. Find the magnitude and position of the balancing mass at a radius of 50 mm,
Please explain each type of motion that would occur in the object if moments were applied in the x, y, and z directions. Thanks!
The spool of cable has a mass of m and a radius of gyration of k. The tension in the cable T is a function of time t, when this in seconds. Neglect the mass of the unwound cable, and assume it is always at a constant radius. a.) What is the moment of Inertia of the spool? b.) What is the angular acceleration of the wheel at t (Use + for the ccw direction)? c.) How quickly is the cable being pulled at time t (Use + for to the right) in m/s? do T d₁ 0 = 60° Variable do d₂ h kc m T TEL Value 1m 0.5 m 2.25 m 0.77 m 100 kg 30t³ +77t N 1.81 s 1352 + 0) N h