13 14. Consider the problem if the scenario happens at a planet with a local acceleration due to gravitation of 12.73m/s?, determine the magnitude of deflection of the spring right after the stoppage. Assume no energy loss during operation.

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: Find the value of x5 in 3 decimal places (positive value) using Secant Method (5th Iteration) f (x)…

A: Write the given equation. fx=sinx-x take x0=0, then  f0=sin0-0=0 take x1=1, then f1=sin1-1=-0.1585

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: 4 mefeor is aout l a gang and is velocity is 4epined by ve t-5, whare is in seconds. Find fre

A:

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: 4 Am ob jecet is made p fravel obrerver çees fhat it is fraveluing harizbufally fx= 24t° M/ where…

A:

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: What is the procedure of using the Mohr's circle?

A: The procedure of Mohr's Circle is given as, (1) Draw the vertical and horizontal coordinates. The…

Q: travelling hoizoniany obenier fees ma where t is in seconds. What s the magnitude and vecE of the…

A:

Q: a boe is foaveling parth of How/ong illake par the bus reach la5 on sap a conctant speedf a

A: Given:v=17 m/sS=5 km =5000 m

Q: Draw the Venn Diagram and write your answer in set roster notation. 5 pts A={1,2,3,4} B ={1,3,5,7}…

A: Venn diagrams are used to establish relation between things or a finite group of things with the…

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

A:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: Question No. 5 Find out the missing number in the series given below: 6, 13, 28, 59, ?, 249 O 124 O…

A: here, (6×2)+1 =13 (13×2)+2= 28 (28×2)+3 =59 (59×2)+4 = 122 (122×2)+5 = 248

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: Represent the following as a number between 0.1 and 1000 using an appropriate prefix:568(10^5)mm

A: Given: The given number is N=568×105 mm. The conversion factor to convert the given unit in the…

Q: Find the value of x5 in 1 decimal places (positive value) using Newton-Raphson Method f(x) = 2x2 + x…

A:

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True O False

A:

Q: Is this for number 1 only?

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: 6-a toy sparechúp is attached by asiring ts a ceiling fan and a the fan atatas the spiceship trauefs…

A:

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.