120 mm A V B D 300 mm 80 N 80 N B 30 mm A 30 mm D D 12 mm 12 mm

Q: 2. For the frame shown, calculate the reactions at A and B. 240 lb 90 Ib/ft 30 Ib/ft A 20 ft 20 ft…

A:

Q: Can you show how you got the moment for each Force from A?

A: Resolving the inclined forces F1 and F3 as shown in the figure.

Q: (A) Determine the resultant of the two forces and the couple that act on the beam and illustrate in…

A: The cantilever beam is loaded with two point loads and a couple The resultant of the two forces and…

Q: three cables attached to the eybolt apply the forces shown. determine the resultant force applied to…

A:

Q: 4m m 1500 kN 2500 kN 3 2m m 3m m 10 m 4.

A: Given, External forces are 2500 kN and 1500 kN

Q: Please show magnitud and direction for every member forces) Use the method of MEMBERS to determine…

A: Force F = —1500 lb

Q: G, and G2 respectively, determine the tension force in cable AB and the reaction forces at point 0.

A:

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

A: Free body diagram:

Q: Fig. 2 F = 300 N = 250 N 309 60° 2 m 3 m 4 m B F= 500 N Fig. 3

A:

Q: The compound bar is supported by a thrust bearing at A, a slider bearing at B, and the cable CD.…

A: Given Compound bar To find Tension in cable Bearing A reaction

Q: The device shown is used to straighten bowed decking boards just prior to final nailing to the…

A: Given:AB = 176 mmBC = 507 mmRequired:N ( normal force applied to the bent board near point B )

Q: For the force at C, find the reactions at D, E, and A.

A: Solution: given dataF = 10 lb

Q: Q4.A. An effort F is required just to move a certain body of weight 393 N up an inclined plane of…

A: Since you have uploaded two questions and did not specify which question to be solved, as per the…

Q: A construction worker on a job site attempts to move a boulder out of the way by attempting to apply…

A: First, we know a total of "F1 "and "F2 "is equal to "F" and after that, we take a moment about point…

Q: The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal…

A: Find outDetermine the tension in the cable AE.Given(I kip = 1000 lb)Load P = 2 kips = 2000 lbMoment…

Q: Consider the clamping device used to lift a 55 gallon drum, as depicted in the accompanying figure,…

A:

Q: Q2: During a steady right tum, a person exerts the forces shown on the steering wheel. Note that…

A:

Q: m The hoist supports an engine Determine magnitude of the force created by the engine mass

A: tanθ1=a+ba-btanθ1=2.2+1.12.2-1.1θ1=71.56o∑Fv=0RA+RB-mg=0RA+RB=mgRA+RB=175×9.81RA+RB=1716.75 N ,…

Q: A homogeneous rod AB weighs 100 N. The end is attached to the wall with hinges, while the B end is…

A: Given Beam weight = 100 NDead weight = 200N To find Free body diagram Tension in rope BC

Q: 45° C d

A: GIVEN:

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which…

A: Given information: The mass of the rod (m) = 18 kg From The figure we can calculate the angel "α"…

Q: 60° 45° 2) For the loaded truss given, determine the forces on each of the member by method of…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: a. A plate is supported by 4 concurrent forces. If the resultant force on the plate is zero what…

A: The number of cun-current forces, n = 4The resultant force = 0

Q: 45° Smooth surface B 0

A:

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is…

A:

Q: The structure is made of the light bar AB and the 50-kg uniform bar CD. Compute the magnitude of the…

A:

Q: Determine the forces in AB and BC and indicate the direction of each.

A:

Q: Given: P = 23 kN a 3 1.3 m b = 1.2 m c = 1.4 m d = 1 m 8 = 33° Required: DO NOT INCLUDE AN Y SIGN By…

A:

Q: The wall-mounted 3kg light fixture has its mass centre at G. Determine the vector reactions at A.

A:

Q: The force in member CD of the given truss

A: given truss as shown below

Q: Determine graphically the forces FAB and FAC

A:

Q: 1. Determine the force, 'P' required to prevent the wheel of weight 115-lb from rolling down the…

A: Consider the free body diagram of the wheel as shown below.

Q: Problem 3. Determine the vertical clamping force at E in terms of the force F applied at the handle.…

A:

Q: The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: Two squirrels are sitting on the rope as shown. The squirre found less food this season and has a…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.