12.Which surfaces in the top view does line K of the front view represent ? ______________ 13.Which surface in the top view does line M in the front view represent ? ______________ 14.Which line in the side view represents the same surface represented by line M of the front view ? ______________________

Q: The sun is the only star whose size we can easily measure directly; astronomers therefore estimate…

A: LB=10,000×LS

Q: Q/ Draw a Top view with the dimensions written on it -20 -20 -20-10 30 10 50 10 Top View?? 20 20 10

A:

Q: The velocity of light in space is approximately186,000 mi/s. The velocity of light in units of…

A: Given: The velocity of light in space is V=186000 mi/s.

Q: A person whose eyes are H= 1.53 m above the floor stands 2.20 m in front of a vertical plane mirror…

A: According to the given dataH=1.53 mD=2.20mh=38cm=0.38md=xWe need to findDistance x

Q: What changes we must make in experimental arrangement in order to find maximum K.E of…

A: What changes must be made in experimental arrangement in order to find maximum K.E of photoelectrons…

Q: What does view one represent in this flange?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Problem. 1 (Fig. 7-61): Draw according to 3rd angle projection method the following views of the…

A: The front-view of the 3-rd angle projection of the given object is as follows.:

Q: The strongest colors reflected in a thin film have wavelengths in the film equal to of the thinnest…

A: Optin C is answer in first question   The brightest colors are those that interfere constructively…

Q: 1. The object that enable us to tivate end points, tangent, centers, midpoints, etc. is .

A: Explanation: The object that enable us to activate end points, tangent, centers, midpoints the…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please check

A:

Q: (Extra) Prove that for a spherical mirror: a) So=f(MT-1) /MT b) Si = -f (Mr-1) %3D

A:

Q: I can't seem to visualize the missing side. Any help would be appreciated

A:

Q: Q1(b): Taking X as the lowest view point, sketch the isometric view of the part.

A: We must combine the three views to get the 3 dimensional view of the object. Dotted lines indicate…

Q: Weather radar provides information on the intensity as well as the total amount of precipitation.…

A: Given Data Reflective value at which the value need to calculate is: RV=47 dBZ The amount of time…

Q: 3) Why does your breath feel cool when you blow air quickly out of your mouth onto your hand ? (Hint…

A: The convection heat transfer from a surface is a function of velocity of fluid flowing over a…

Q: Resolving power of an spectroscopic instrument is increased when...

A: Resolving the power of spectroscopic as the minimum wavenumber, frequency or the wavelength which is…

Q: ind the apparent solar time (AST) corresponding to 8:00 a.m. central time on July 21 in Phoenix, AZ,…

A: Given: The day=21 July Location=Phoenix Longitude L'=112°W Northern longitude N'=33.43°

Q: Two panels of different materials are spaced 6m apart and at a 30-degree angle.  The top panel is 2m…

A:

Q: Hello dear Expert!  Please kindly shade the region of intersection of the curves of the cylindrical…

A: FindEstablish on the different views, the layout of the intersection curves.

Q: How can a light source help to create the illusion of depth and volume? Explain with an example of…

A: A light source can create the illusion of depth and volume by casting shadows, highlighting…

Q: At 40º north latitude, on 22 December, array collectors are required to see direct sunlight for at…

A:

Q: Determine the viewfactor F1-2 for the figure below

A:

Q: 4. Spectra and filtering. a. White light has an approximately constant spectrum in the visible range…

A: Here the spectrum is drawn as an ideal case , hence It will Have the sharp turns But in reality it…

Q: 1.Explain how X-ray absorption can be used to design X-ray filters

A: The X ray filters are used to reduce the intensity of the emitted X ray from its spectrum. The X…

Q: 2. Which of the below figures is the right-side view of the object shown in the illustration below?…

A: Introduction: Principal planes are horizontal or vertical planes that are parallel to one another.…

Q: An object immersed in water at a depth of 1 m appears to be closer to the surface. Find the apparent…

A:

Q: Draw the full auxiliary and the partial auxiliary views in the areas labelled below.

A: full auxiliary and the partial auxiliary of the given object is required at the given space…

Q: An industrial engineer designed a workstation where the seeing task was difficult because of the…

A: (1) Write the given data. Brightness or Luminance, E=150 ft·LambertReflectance, R=0.52

Q: Taking X as the lowest view point, sketch in the space provided, the isometric view of each object.

A:

Q: Choose the correct Front View from the following isometric view. 50 10_20 30 90 60

A: Given :- Orthographic 3 D view Find:- Front view of the object

Q: 15 VIEW 2 44 32

A: following is the answer to the above problem-

Q: Unpolarized light passes through successive polarizers sheets, each of whose axis makes a 20° angle…

A:

Q: Calculate the minimum row spacing for a ground-mounted array in Las Vegas, NV. Assume the height of…

A: The given data are: θ=10°d=10 ft Here, θ denotes the angle and d denotes the distance.

Q: A DVST, or Direct View Storage Tube, is a kind of optical storage medium.

A: Introduction A direct-view storage tube is similar to a cathode ray tube in that it employs an…

Q: What is the name of the figure or 3D model

A: Given 3D model To find Figure name

Q: GIVEN: FRONT AND LEFT SIDE VIEWS. SKETCH: AUXILIARY VIEW PROJECTED OFF THE FRONT VIEW. SHOW VISIBLE…

A: Auxiliary view An auxiliary view is an orthographic view taken in such a manner that the lines of…

Q: 1.1 x 10-3 2.89 x 10-4 9.56 x 10-4 2.0 What are the 2.2 2.4 angles of refraction when 2.6 3.17 x…

A:

Q: Find the point of view lines of the given

A: Point of view at AB in HRP

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.