12. A single-phase, 120 V, 60 Hz, 1/2 hp, 1740 rpm split-phase fan motor gave the following testresults:VIPNo load test1204110Standstill test (main winding)415.8 115Standstill test (auxiliary winding)387200Main winding resistance = 1.85 Q.a) Obtain an equivalent circuit for the motor for running conditions.b) Determine the no-load rotational loss.c) Determine the efficiency at the rated speed.13. For the motor in Problem 12:a) Determine the standstill impedances of the main and auxiliary windings.b) An external starting resistance R$ =22 is added in series with the auxiliary windings, and the motoris connected to a lø, 120 V, 60 Hz supply.i. Draw a phasor diagram of the currents Im and Ia, and the voltage V, with and without the addedresistance R,.ii. Compare the starting torques and starting currents with and without the added resistance.14. Repeat Problem 13 if an external starting capacitor Cs =500 µF is added in series with the auxiliarywinding.

12. A single-phase, 120 V, 60 Hz, 1/2 hp, 1740 rpm split-phase fan motor gave the following test results: V I P No load test 120 4 110 Standstill test (main winding) 41 5.8 115 Standstill test (auxiliary winding) 38 7 200 Main winding resistance = 1.85 Q. a) Obtain an equivalent circuit for the motor for running conditions. b) Determine the no-load rotational loss. c) Determine the efficiency at the rated speed.

12. A single-phase, 120 V, 60 Hz, 1/2 hp, 1740 rpm split-phase fan motor gave the following test results: V I P No load test 120 4 110 Standstill test (main winding) 41 5.8 115 Standstill test (auxiliary winding) 38 7 200 Main winding resistance = 1.85 Q. a) Obtain an equivalent circuit for the motor for running conditions. b) Determine the no-load rotational loss. c) Determine the efficiency at the rated speed.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A repulsion start, induction run motor is used to drive a fan. The motor has a rated power of 2kW and operates at 220V. The repulsion start winding has a resistance of 0.5 ohm while the induction winding has a resistance of 0.3 ohm. Determine the total loss in the motor, assume 0.8 pf.
A. The DC motor in Figure 1 on Worksheet 8 is a a) cumulatively connected short-shunt compound DC motor b) cumulatively connected long-shunt compound DC motor c) differentially connected short-shunt compound DC motor d) shunt DC motor B. The DC motor in Figure 2 on Worksheet 8 is a a) cumulatively connected short-shunt compound DC motor b) cumulatively connected long-shunt compound DC motor c) differentially connected short-shunt compound DC motor d) shunt DC motor
H.W 1) A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Q and the contact drop is 1 V per brush. Calculate the full-load speed of the motor. H.W 2) A d.c. series motor with series field, and armature resistance of 0.06 ohm and 0.04 ohm respectively is connected across 220 V mains. The armature takes 40 A, and its speed is 900 rpm. Determine its speed when the armature takes 75 A, and excitation is increased by 15% due to saturation.
Q/Two dc generators A and B has the following characteristics:GA: rated voltage=150 volt: rated carrent=30Ampere: armature resistance (0.4Ω).GB:no_lond voltage=160Volt: rated carrent=20Ampere: armature resistance=(0.6Ω).The generators are connected in paralled. Draw the circuit diagram, then find:no_load circulating current and no_load voltage?At what carrent the generator B will Be floating? The maximum possible land power
A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be
7. show the solution and draw a figure
A three-phase star-connected alternator working at 1400 KVA,50 Hz, 2300 V, has an armature dc resistance of 0.15 2. Assume the ac resistance is 1.4 times the dc resistance. A field current of 75 A produces a short circuit current of 360 A and for the same field current the open circuit voltage is 1000 V. Determine a) Synchronous reactance of the machine b) Full load regulation at 0.9 leading c) Power angle a) b)
G1. The terminals of a DC motor are identified as the same as those of a DC generator. a) true b) false G2. What are the standard identification letters for the armature winding of a DC compound motor? a) A1 and A2 b) S1 and S2 C) F1 and F2 d) none of the above G3. What are the standard identification letters for the series field winding of a DC compound motor: a) A1 and A2 b) 1I and S2 c) F1 and F2 d) none of the above