12. A shaft is supported in two bearings 8 ft. apart and projects 2 ft. beyond the bearings at each end. The shaft carries three pulleys, one at each end and one at the middle of its length. The end pulleys weigh 180 lb. and 100 lb. and their centres of gravity are at 0-15 and 0-20 in. respectively from the shaft axis. The centre pulley weighs 140 lb. and its centre of gravity is 0-25 in. from the shaft axis. If the pulleys are arranged so as to give static balance, determine the dynamic forces produced on the bearings when the shaft rotates at 300 r.p.m.

12. A shaft is supported in two bearings 8 ft. apart and projects 2 ft. beyond the bearings at each end. The shaft carries three pulleys, one at each end and one at the middle of its length. The end pulleys weigh 180 lb. and 100 lb. and their centres of gravity are at 0-15 and 0-20 in. respectively from the shaft axis. The centre pulley weighs 140 lb. and its centre of gravity is 0-25 in. from the shaft axis. If the pulleys are arranged so as to give static balance, determine the dynamic forces produced on the bearings when the shaft rotates at 300 r.p.m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

12'-0" 5'-0" 3'-0" 4'-0" window door 3'-0" 4'-0" 4'-0" 3'-0" 25'-0" 11'-0" A pre-cast concrete wall panel with one door and one window opening is to be hoisted into position at a building site. When hoisting the wall panel, it will be useful to know the location of its centroid. Determine the centroidal X and Y axes, referenced from the lower left corner. Clearly show the location of the centroid on the drawing.
7. Locate the centre of gravity of the homogeneous bodies as shown in the figure below. 40 in. 30 in. 1.5 in. 1.5 in. 20 in. 10 in. diam.
Determine the centroid of the given figure. 120 mm 60 mm 40 mm 80 mm 60 mm O x = 55.45 mm and y = 35.65 mm %3D O x = 53.70 mm and y = 37.70 mm O x = 56.83 mm and y = 37.62 mm O x = = 54.10 mm and y = 36.30 mm O x = 53.56 mm and y = 35.63 mm O x = 56.80 mm and y = 37.10 mm O x = 55.76 mm and y = 36.65 mm O x = 54.80 mm and y = 36.60 mm
Verify that the radius of gyration for a circle of diameter d with respect to a centroidal axis is r = d / 4.
Problem 6 Compute Ix and Ix for the shaded region (Hint: first find the y centroid of the composite area). 7.5 3 3+ Dimensions in inches
The post has a rectangular cross-sectional area. It is fixed-supported at its base and the loadings are applied as shown. The 500N force acts on the centroid of the cross-sectional area, the 400N force acts at the corner and the 300N force acts on the side of the block, along the axis going through the centroid. A and B are in the same cross-section. B marks the corner point, A is located on the edge, a distance of 5 cm from point B. a. Draw a section cut and find the internal loadings at a cross- section containing point A. You MUST use the coordinate directions we used in our class example (x-axis down, y-axis out of page, and z-axis to the left). 300N 30cm 30cm 20cm 80cm 400N 20 cm 20 cm A 500N
04) In the figure shown, determine the centroidal coordinates and moment of inertia about x & y-axis, if the value of b=4 in. 0.5 in L3x3x -5 in -5 in
Determine the height h above the base of the centroid of the cross-sectional area of the beam. Neglect the fillets. Assume a = 11.76 in., b = 12.58 in., c = 1.17 in., d = 5.81 in., e = 0.54 in. FI ko Answer: h= i in.
Question 2 Calculate the following: i. The centroid ii. Moment of inertia of the channel section about the x'-axis 25mm 25m 100 mm 25 mm 25 mm 75mm 75mm 50mm 50mm' 100mm 25 mm
Find the value of the y-component of the centroid given x1 = 0.9 m, x2 = 0.22 m, x3 = 0.58 m, and y1 = 0.12 m and y2 = 0.8 m. Report your answer in meters to three decimal places. ylm y2 m yl m y x1 m x2 m x3 m ·X
find the center of gravity of a semicircular section having inner and outer diameter of 200mm and 160mm
Determine the slope of the 50-mm-diameter A-36 steel shaft at the journal bearings at A and B. The bearings exert only vertical reactions on the shaft.