12) The pressure gauges 1, 2 and 3 are installed on the system as hown. If the readings of the gauges be P1 -1 bar, P2- 2bar and Ps-3 var, what will be the valuc of P? (Take Pam 1.01 bar)

Q: Date No. A diffevential manometer is connected at two puints A and B of two pipes as Shown on the…

A:

Q: kerosene, s = 0.82 A manomoter is usod to moasuro tho pressure of air shown. Solve the pressure at…

A: Let the gauge pressure at A = PA Density of mercury=13.6×103 kg/m3 Density of oil = 0.80×103…

Q: 94 In the figure, in +he water 0,IM -(2) Alow in the T -shapped pipe inthe horizental plane, the…

A: Following is the given T-Shaped pipe in the horizontal plane:   To find: x and Ycomponent of the…

Q: Show complete and clear solution. Don't round off initial values, round off final ans only pls

A:

Q: Determine the value of h in mete

A:

Q: An aluminum tube of 3-in. outside diameter is to carry a load P of 10 kips having an eccentricity e…

A: D = 3 in P = 10 kipse = 0.6 in

Q: 5) Determine the FF. L Be вку 3. Stress BD 2. 7 RE

A: Given figure shows a truss. It is required to calculate stresses in member BD,BE, CE and also to…

Q: دلها ↓↓ P 7 B vwx What is the Reaction Force induced in the following system at point A, if? Wo = 7…

A: A beam is given we need to find out the reaction at A

Q: H.w.: As shown in figure below, determine the pressure at point. A- Hg Ans.: 12.164 KPa Va cuum…

A:

Q: SP 1 The diameter in fig are 90 cm and 60 cm, at the larger end the pressure is 9.81 kpa, neglecting…

A:

Q: Find the Sarce. narmal

A:

Q: gitudinal and circumferenti

A: first take a cross section AA ans BB  in the given figure and then analyse the area carefully

Q: An A-36 steel tubular shaft is 1 m long and has an outer diameter of 40 mm. When it is rotating at…

A:

Q: The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application…

A: Given,  Maximum force = 20 KN.  Air pressure = 700 kPa. Piston rod length l= 760mm.One end pinned…

Q: 2 1 5. v=R3S2 n hf 10.29n²LQ² D16/3

A:

Q: mplete solution pls answer in 20 m

A: Take moment about C∑ Mc=0TBA0.125-10000.3=0TBA=2400N∑ Fx=0TBA-Cx=0Cx=2400N∑ Fy=0 Cy=1000N…

Q: The 350-N lamp is supported by three steel rods connected by a ring at A. The average normal stress…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: A cast ALuminum cr linder of ļ a yortable hvdrauli c riveter is 208 mm in odiameter The Pressure. of…

A: Since the outer pressure is not provided, the tangential and radial stresses cannot be obtained.…

Q: A solid shaft in a rolling mill transmits 20 KW at 2r/s. Determine the diameter of the shaft if the…

A: Given: The power is 20 kW. The frequency is 2 Hz. The maximum shear stress is 40 MPa. The angle of…

Q: Q2: An oil of Viscosity Co.15 pa.s) and specific gravity 0.9 is flows Throngh an inclined (300mm)…

A: The slope for constant pressure throughout the pipe is given by: sinθ=-32μVγD2 Where, V = Velocity…

Q: From the following system determine: a) the pressure at A, B, C, D b) the velocity at A, B, C D c)…

A: Pressure- Pressure is defined as the external force applied per unit area. When fluid is in rest…

Q: Describe about the piston with pressure chamber in the statnamic test.

A: The statnamic test is the tests which are used for determining load carrying capacity of deep…

Q: Which one is correct? A. Increasing additional load means increasing exposed depth in a fluid. B.…

A:

Q: The assembly of pipes consists of galvanized steel pipe AB and BC connected together at B using a…

A: Given data: Length of pipe (AB)1=1m Inner Diameter=17 mm Outer diameter=20 mm   Length of pipe(BC)…

Q: Determine the AV (change in volume) of the 8-in. length of the rod shown if the rod is made of steel…

A: The basic relation between bulk modulus and young's modulus is          E = 3K1-2×μ29×106 =…

Q: Water at 25°C is pumped into the galvanized iron pipe branch consisting of two 50-mm-diameter pipes…

A:

Q: 1. Find the simplest resultant of the pressure distributions on plates Lxb 90 L 90

A:

Q: Determine the minimum thickness of the tank plating if the internal pressure is 1.3MPa and the…

A: Internal pressure=1.3MPa Allowable stress= 38MPa To find minimum thickness of tank

Q: find Q? and pressure at each pipe L. 7om dsolm LEioum dso es fzoul

A: Applying bernoulli's equation between tank 1 and tank 2P1pg+V12g+z1=P2pg+V22g+z2+hf               eq…

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: First solve AB and then BC. For W= 789.

A: To determine:FBD, Support reactions, SFD and BMD

Q: 2. Find the maximum value of P that can be exerted on the two pistons so hat the tangential stress…

A:

Q: O-0.13 Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two…

A: given- Hydraulic head at 1, h1=24 inchesHydraulic head at 2, h2=11 inchesdistance travelled, L=100…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?