12 mm 300 N 120 mm 96 mm 300 N 36 mm 42 mm 30 mm 30 mm 6 mm PROBLEM 6.148 Determine the magnitude of the gripping forces produced when two 300-N forces are applied as shown.

Q: All members of the truss have the same length L=3.9 m. Determine the MAGNITUDE (N) of force…

A: Given:

Q: Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A.…

A: The force is The length of handle is

Q: Problem 7: Values: h=4m a = 1.5 m b=2m FB = 400 N Fc = 600 N Determine the magnitude of the…

A: Given data  h= 4 m, a= 1.5m , b= 2m And FB = 400N, FC = 600N Find the magnitude of resultant force…

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

A:

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: please refer handwritten solution

Q: Replace the loading shown by a single equivalent force. Specify the magnitude and direction of this…

A:

Q: Consider the clamping device used to lift a 55 gallon drum, as depicted in the accompanying figure,…

A:

Q: Part A When y is zero, the springs sustain a force of 54 lb. (Figure 1) Determine the magnitude of…

A:

Q: 600 N 600 N 40 250 N 250 N

A: Given Couple moment = 500 Nm To find Magnitude of F

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A:

Q: 3. Determine the magnitudes of the pin reactions at A and C. Neglect the weights of the members. 800…

A:

Q: Add the following forces to find the resultant force. V1 = 150 g @ 470 V2 = 550 @ 324° V3 = 350 g @…

A:

Q: The spring AB has an unstretched length of 252 mm and stifness k=842 N/m. In the configuration…

A: Lo=252mm=0.252m K=842 N/m L=576mm=0.576m   To find: FBD

Q: 5. Mystery Problem The thin uniform plate with dimensions 26m X 28m as shown weighs 2000N and is…

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: please refer handwritten solution below

Q: A structure ABCD is supported by a slider bearing at A, the cable BE and a thrust bearing at D. If…

A: Draw the free-body diagram of the system.

Q: Determine the force in cable AB and support C.

A:

Q: e ANSWER ALL of the given questions and show COMPLETE SOLUTION for each question.   I will rate…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: Four sets of flexible cables, spaced at 120° intervals, are used to stabilize a 400-ft…

A: Draw the free body diagram of the section containing point A: The axial force transmitted through…

Q: 5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body…

A: Given: Mass of the body is 70 kg. Tendon makes an angle of 8 deg.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.