12) F E DA The framework ABCDEF is smoothly supported at A and D and carries weights of 200 N and 100 N at B and C. Find the forces in the rods FE, BE and CD.

Q: One mole of a monoatomic perfect gas is allowed to expand adiabatically and reversibly from a…

A: Given:Gas is mono-atomic and considered as perfect gasNumber of mole = n = 1For mono-atomic gases,…

Q: 1. A 100 mm deep stream of water (p = 1.14 x 10-³ Pa.s) is flowing over a boundary. It is considered…

A:

Q: 1. Determine the reaction and moment at point A. State the direction of the force. 1 kip/m 15 A 2…

A: Given loading diagram is Let, Ax = reaction force at point A in horizontal directionAy = reaction…

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: 6- In a sand-casting operation, a part whose side view and top view are shown below is to be made.…

A:

Q: the mercury 2. Mercury is poured into the tube in the figure until occupies 375 mm of the tube's…

A: Consider the length of the mercury above the horizontal surface.x1 + x2 =375 mm - 160 mm x1 = 215…

Q: 2.) An Isothermal process is done on air, and it has a pressure of 500 kPa and a volume of 0.5m3.…

A:

Q: The speed of a particle can be negative or positive, depending on the sense in which the particle…

A: It is required to evaluate given statement

Q: Annealing is a process that can release the residual stress and make the grain size grow larger,…

A: Hardness inversely proportional to squere of grain size so option a was wrong.

Q: 9. Glycerin (SG = 1.26) and µ = 1.49 Pa.s) flows through a rectangular conduit 300 mm by 450 mm at…

A:

Q: 4. If 6.5 m³ of oil weighs 46,800 N, calculate its density in kg/m³. (a) 285 (b) 258 (c) 82 (d) 734

A: Given : volume of oil , V = 6.5 m3             weight of oil , W = 46800 N To find : density

Q: An industrial bandsaw of total length L = 11 m and width w = 0.218 m is tightened between two…

A: Given:The length of the band-saw is the width of the band-saw is the diameter of the wheel is the…

Q: *8-36. The drill is jammed in the wall and is subjected to the torque and force shown. Determine the…

A: The free body diagram of the system is as follows.

Q: List down the formulas for calculating the shear stress and angle of twist of the following cross…

A: It is asked to write the shear stress and angle of twist formula for the cross-sections of shape…

Q: 5. Find the total weight of a 10 ft³ tank of oxygen if the oxygen is tank itself weighs 150…

A: Please find the solution below

Q: 3. For the gate shown, α = 45°, Y₁ = 1 m, and y₂ = 4 m. Will the gate fall or stay in position under…

A: Please find the solution below

Q: Calculate the critical resolved shear stress (magnitude) in crystal if a stress of 100 MPa in the SP…

A:

Q: 01: Write G code to Write the first Letter of you name

A:

Q: 12. The composite bar in the figure is stress-free before the axial loads PI and P2 are applied.…

A: FBD of each material :where  δal is shortening length δst is lengthening lengthδbr is also…

Q: 2. Why a pulsed mode generator with a very small duty cycle is needed in the forward voltage…

A: A device that produces regulated, intermitten signals at particular nodes within a system or circuit…

Q: Please answer in typing format

A: System DescriptionThe system consists of two masses, labeled as m1​ and m2​.Springs (k1​) and (k2​)…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

A:

Q: 3.) Air is heated in an Isometric process where the pressure increases. It initially has a state of…

A:

Q: Explain the difference between Turbofan and Turbojet engine and the advantage and disadvantage for…

A: Turbofan - A turbofan engine has a large fan at the front which takes(sucks) the air around the…

Q: What is the name of the part ? What is the part's drawing number ? How many parts are required ?…

A: 1.What is the name of the part? Ans:-FEED HOPPER 2.What is the part's drawing number? Ans:-A-11…

Q: If the cords suspend the two buckets in the equilibrium position, determine the weight of bucket B.…

A: According to the given data  weight of the bucket-A= 60 lb we need to determine the weight of the…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.