12 A line shaft ABCD, 9 metres long, has four pulleys A, B, C and D at equal distance apart. Power of 45 kW is being supplied to the shaft through the pulley C while the power is being taken off equally from the pulleys A, B and D. The shaft runs at 630 r.p.m. Calculate the most economical diameters for the various portions of the shaft so that the shear stress does not exceed 55 MPa. If the shear modulus is 85 GPa, determine the twist of the pulley D with respect to the pulley A. [Ans. 28 mm, 36 mm, 28 mm; 0.0985°]

12 A line shaft ABCD, 9 metres long, has four pulleys A, B, C and D at equal distance apart. Power of 45 kW is being supplied to the shaft through the pulley C while the power is being taken off equally from the pulleys A, B and D. The shaft runs at 630 r.p.m. Calculate the most economical diameters for the various portions of the shaft so that the shear stress does not exceed 55 MPa. If the shear modulus is 85 GPa, determine the twist of the pulley D with respect to the pulley A. [Ans. 28 mm, 36 mm, 28 mm; 0.0985°]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hollow shaft is required to transmit 700 kW at 110 r.p.m., the maximum torque being 20% greater…

Q: In Figure 2, the shaft is made of a solid A992 steel at section AB (ra = 25 mm), Ti-6A1-4V titanium…

A: r1=15mmr2=20mmr3=25mmT=120N-md1=30mmd2=40mmd3=50mm To-Find:- Resultant Angle of twist at D

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A: Given data:

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…

A: for solution refer below images.

Q: compound shaft consists of segment (1), which has a diameter of 1.7 in., and segment (2), which has…

Q: Determine the size of the shaft,

A: Given: P=22 kW N=550 rpm shear stress=42 MPa Tensile/compressive stress=56 MPa P=900 N L=2.5 m To…

Q: ches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable…

Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…

Q: 2 A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a…

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supplies by motor is The speed of motor is The diameter of shaft 1 and 2 is The modulus of…

Q: Problem 5

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

Q: A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the…

Q: A steel tube of outer diameter 86mm and inner diameter 52mm is under pure torsion. The diameter of a…

A: Outer diameter = 86 mm Inner diameter = 52 mm Answer is (B) 81.98 mm

Q: A solid shaft is transmitting 1 MW at 250 r.p.m. Determine the diameter of the shaft if the maximum…

A: As per our guidelines we have to answer one question only so, post the question separately and…

Q: Finding the value of sectional modulus of shaft having diameter 3 m

A: Given data : Diameter of shaft is given in this question . With help of this data we have to find…

Q: 2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the…

Q: Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree…

A: Given Data P=30 MW N=1500 rpm Angle of twist=1° L=20D G=80 GN/m2

Q: 2. The solid shaft AB has a diameter d_s = 1.5 in. and is made of steel with a shear allowa of 12…

Q: Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is…

A: For solution refer below images.

Q: -1-60 in. and L2= ne the maximum shear stresses T₁, ne the rotation angle DA of gear i in.,…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: The 4-In. diameter shaft shown above is made from a ductile brass alloy. Which of the following are…

A: Normal Stress = Force / Cross Section Area = 4*100 / (π 4^2) = 7.957747154 Ksi Shear force is to be…

Q: 3. Find the diameter of a solid steel shaft to transmit 27 kW at 300 r.p.m. The ultimate shear…

A: Given:-Power, P=27 kWSpeed, N=300 rpmUltimate shear stress, τu=360 MPaFactor of safety, FOS=8Ratio…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: Given DataInner tuber1=20mmro=25mmCentre tuber1=26mmro=30mmOuter Tuber1=32mmro=38mm…

Q: The drive shaft AB of an automobile is made of a steel having an allowable shear stress of Tallow =…

Q: A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa…

Q: A 3 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 200 HP. The shaft…

A: Given data as question Length of shaft = 3 feet Power of shaft = 200 hp Sped of shaft = 1500 rpm…

Q: A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild…

A: The given values are - P=28×103W , N60=55 rps, ζ=85 MPa P=T.ϖ where…

Q: sections B and C, respectively with a bending load P on section B. Design the diameters at sections…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

A: Shear stress when twisting moment is applied on the shaft ,shaft experiences the shear stress. shear…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100 mmj
12 A line shaft ABCD, 9 metres long, has four pulleys A, B, C and D at equal distance apart. Power of 45
kW is being supplied to the shaft through the pulley C while the power is being taken off equally from
the pulleys A, B and D. The shaft runs at 630 r.p.m.
Calculate the most economical diameters for the various portions of the shaft so that the shear stress
does not exceed 55 MPa. If the shear modulus is 85 GPa, determine the twist of the pulley D with
respect to the pulley A.
[Ans. 28 mm, 36 mm, 28 mm ; 0.0985°]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Partial answer (a) max and min shear stress = +- 10.6 kpsi (b) vB=-0.0102 in and wB=.0234 in
4
8.9 (A/B). A solid steel shaft of 200 mm diameter transmits 5 MW at 500 rev/min. It is proposed to alter the horsepower to 7 MW and the speed to 440 rev/min and to replace the solid shaft by a hollow shaft made of the same type of steel but having only 80% of the weight of the solid shaft. The length of both shafts is the same and the hollow shaft is to have the same maximum shear stress as the solid shaft. Find: (a) the ratio between the torque per unit angle of twist per metre for the two shafts; (b) the external and internal diameters for the hollow shaft. [L.Mech.E.] [2.085; 261, 190 mm.]
Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the allowable shearing stress is 300 Mpa and key width is 10 mm ,determine the length of key.
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
i need the answer quickly
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
Consider the case of shafts subjected to combined twisting moment and bending moment. A solid circular shaft is subjected to a bending moment of 2800 Nm and a torque of 10,000 Nm. The shaft is made of 45 C 8 steel having ultimate tensile stress of 700 MPa and ultimate shear stress of 500 MPa. Assuming a factor of safety as 5, determine, the diameter of the solid circular shaft. if a hollow circular shaft is to be used in place of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameter is 0.5.