12-6. The wood beam has an allowable shear stress of Ta = 7 MPa. Determine the maximum shear force V that can be applied to the cros section. So mm -100 mm- S0 mm So mm 200 mm

Q: 12-14. Determine the maximum shear stres acting at section a-a of the cantilevered strut. 2 kN 4 kN…

A: The cross-section area of the flange is, The centre of gravity of flange about y axis is, The…

Q: If the wide-flange beam is subjected to a shear of V = 20 kN, determine the maximum shear stress in…

A: From the half section above neutral axis:

Q: If the beam is made from wood having an allowable shear stress τ allow = 300 psi, determine the…

A: Given: d = 4.5 in τallow=300 psi   Calculation of reactions: By force balance:     RA + RB = 3P By…

Q: The H-beam is subjected to a shear of V=60 kN. determinate the flow at point A

A: The shear force is

Q: 5) The beam is supported by a pin at A and a shaft link BC. If P = 15 KN, determine the average…

A: Given data  Force p = 15 kn Diameter = 18 mm Each pins are double shear . Find the shear  stress in…

Q: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum shear stress in…

A: The diagram of I-section is given as, The maximum shear stress is written as, The value of Q is…

Q: 2- Determine the maximum shear stress in the T-beam at point C.

A: Given   Loading = 10 kN/m Total length, L = 3 + 1.5 + 1.5 m Find   Maximum shear stress

Q: The wood has an allowable shear stress of Tallow = 6 MPa. Determine the maximum shear force Vthat…

A:

Q: Determine the shear stress at points A and B of the web, when the beam is subjected to a shear force…

A: V = 15 kN w = 125 mm

Q: *12 44. The T-beam is nailed together as shown. If the nailscan each support a shear force of 4.5…

A: Write the expression of the centroid of the T-beam in the y-direction. Write the expression of the…

Q: Determine the internal shear force at a location of x = 0.9 m for the following beam. f(x) = 2…

A: The load = 2(kN/m)Find the internal shear force at x= 0.9m

Q: Determine the maximum shear stress in the T-beam at section C. Show the result on a volume element…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: If the beam is subjected to a shear of V = 15 kN, determine the web’s shear stress at A and B.…

A:

Q: 10-26. A beam is made up of four 50 X 100-mm full-sized Douglas Fir pieces that are glued to a 25 x…

A: Given:- B=125mm D=500mm b=100mm d=300mm Allowable bending stress= 10MPa Allowable shear…

Q: 12-45. The nails are on both sides of the beam and each can resist a shear of 2 kN. In addition to…

A: Draw the free body diagram for the given problem. Now determine the centroid of the given system.…

Q: The boards are bolted together to form the built-up beam. If the beam is subjected to a shear force…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: Determine the reactions at points A ,B and o.Also determine the resultant internal loadings in the…

A:

Q: 0.5 in.3 in C 0.5 in. 3 in. 10 in. 0.5 in. B M

A: The centroid of the given figure is-The centroidal moment of inertia-

Q: Two identical 20-mm-thick plates are bolted to the top and bottom flange to form the built-up beam.…

A: The above figure shows the crossection of the section. 1 represent the big rectangle of the…

Q: Q.2// The beam is supported by a pin A and a short link BC. Determine the average shear stress…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: A beam is constructed from two i-sections as shown in Fig. Determine the maximum shear stress if the…

A:

Q: Determine the internal shear force at a location of x = 1.0 m for the following beam in kN. ا f(x) =…

A:

Q: Determine the shear stress Given shear force 20 KN , Rectangular cross section= 30 mm*20 mm

A: Given data : Shear force (V)=20 KNArea(A)=30×20=600 mm2

Q: A beam is constructed from three boards bolted together as shown. Determine the shear force in each…

A: Consider the diagram shown below for the cross-section of the beam.

Q: If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web…

A: The moment of inertia about the neutral axis: I = 0.2×0.34312-0.18×0.3312I = 2.50×10-4 m4Section…

Q: If a = 3 in. and the wood has an allowable normal stress of sallow = 1.5 ksi, and an allowable shear…

A: The section modulus of the rectangular cross-section about the neutral axis is…

Q: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the shear force resisted by…

A: Average shear stress in a beam is given by, τavg = VQI t   Where V = Transverse Load applied on…

Q: Determine the normal and shear stress on section a-a that passes through the centerline at point C…

A:

Q: The beam is subjected to a shear of V = 850 N  Determine the average shear stress developed in the…

A:

Q: *11-8. The simply supported beam is made of timber that has an allowable bending stress of oallow =…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: *7-16. The beam has a square cross section and is made of wood having an allowable shear stress of…

A: given data as per the question Allowable shear stress = 1.4 ksi value of shear subjected = 1.5 kip…

Q: Determine the maximum shear force V that the strut can support if the allowable shear stress for the…

A: Given data:  allowable shear stress (τallow) = 40 MPa =τmax Find, Maximum shear force (Vmax)

Q: Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 kN.

A: Given data V=20 KN

Q: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum shear stress in…

A: Given data: Shear force acting at point A, V=30 kN