12" 6" %3D4'

Q: A cantilever beam ABCDE is loaded as shown. If the flexural rigidity is 5 kN-m?, determine the…

A: As per company's policies We are supposed to answer only first three questions  Kindly post other…

Q: 1. Air (p= 1.23 kg/m³; = 1.79x107 through a 0.08-mm-diameter passa person's lungs at a rate of 10-9…

A:

Q: A TRAPE ZOIDAL CHANNEL WITH SIOES INCLINED 36° WITH THE HORIZOMAL ANND A 5.erm Bottomn WITH IS LA'D…

A:

Q: Same elevation - Water T-10°C Machine A

A:

Q: The tower for Telecommunication Company is to be constructed near Mt. Pinatubo. It is observed that…

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take di = 30 mm,…

A: Determine the average normal stress at the midsection of rod BC.

Q: Find the centroid of the area of a trapezoid that has two equal slanting sides, a 12in base and a…

A:

Q: 4) The frontal surface area of a cyclist has been measured as 0.8 m². Knowing that the coefficient…

A: Given data v = 40 km/h = 11.12 m/s p = 1.29 kg/m^3 CD = 0.6 A = 0.8 m^2 To Find :- horizontal force…

Q: Find the volume of each component. 0.2m thickness

A: Given : Thickness, t=0.2 m   To Find : Volume of each Component

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform…

A: A tapered circular rod of diameter varying from 20 mm to 10 mm,Uniform circular rod of diameter 10…

Q: X'= Gs-lx

A: The specific gravity of the soil solids is defined as the ratio of the weight of a given volume of…

Q: Determine the stability and determinacy of the figures.

A: If the degree of indeterminacy is less than zero then the structure will not be stable. Otherwise…

Q: (a) Determine the reaction at A (including share force and bending moment if available) and draw the…

A: E= 200 GPawo=20 kN/mL= 5mb=50 mmd=150 mmTo determine- a) Reaction at A, shear force and bending…

Q: The beam is supported at A and B as shown in (Figure 1). Suppose that F = 6 kip and w = 450 lb/ft.…

A: hinge support at B is givenroller support at A is givenUDL of 0.45k/ft acting over entire spanFind1)…

Q: roblem 3 s shown in the figure below, find the Tension in each portion of these cables and also…

A: The given data: FN=130 kg Assuming ,θ1=30°θ2=60°θ3=30°

Q: Three consolidated-undrained tri-axial tests were performed on samples retrieved from a 4 meter…

A: GIVEN DATA :- TEST  CHAMBER PRESSUER DEVIATOR STRESS PORE PRESSURE 75 75 166 -12 150 150 295…

Q: 4. For the truss shown, determine the forces in members AB, BG, ED and GF 6 kN 2.4m B 24m C 24 m D…

A:

Q: A column 3m long and pinned at both ends carries an axial load of 190 KN. The column is made up of…

A:

Q: A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown.…

A: A square box beam is made of 80 x120 mm s=50 mm allowable shearing force= 300N As the maximum…

Q: Given are the interior angles of a heptagon. Determine the discrepancy for the givenobservation and…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

A: Given, A section,

Q: Let w = [w] lb/ft. p) Determine the maximum shear Vmax in the beam. q) Determine the maximum bending…

A: Given  W= 250 lb/ft

Q: 20ド Sm 10m

A:

Q: y-axis 200+Y (mm) 250 mm Y (mm) 125 mm 60 mm 125 mm х-ахis Determine the total area of the composite…

A:

Q: The formula of the gate is 1/2bh why your formula is A=ab? why there is no 1/2?

A: There is given a triangular gate. Which is inclined at 45° with water surface.

Q: 1. Determine the diameter of solid shaft which will transmit 440 kW at 280 rpm. The angle of wist…

A: Power P = 440 kW = 440×103 W.N = 280 rpmLength L = 1 m = 1000 mmAngle of twist θ=1o=1×π180radMaximum…

Q: PROBLEM 01: A hollow cylinder 0.80m in diameter and 1.2m long weighs 250kg. lead d=1m d=1m lead…

A: ASKED: To determine the volume of lead attached to: (a) outside of the cylinder (b) inside of the…

Q: -Compute the plastic section modulus of the following section and its corresponding moment capacity.…

A: to find - plastic section modulus (Zp) and corresponding moment capacity (Mp)

Q: Q2: Determine (Y). If PA- Pg 6624

A: To solve this problem,  we are given  Pressure at A - Pa Pressure at B - Pb Pa-Pb=6624 We ned to…

Q: ACTIVITY PROBLEM - The following are section notes of a five-level section Station 1+ 125 ? 12.0…

A:

Q: Cost Alternatives; Study Period > Useful Life; MARR = 15% A B Investment cost $14,000 $65,000 Annual…

A:

Q: A VA 3 m 2 N ↓ 3 m

A: