Take note that the cross sectional area is 1.6 in2 and given in the figure is 36 kips 111. For the truss shown in Fig. P-111, calculate the stresses in members CE, DE, andDF. The cross-sectional area of cach member is 1.8 in.. Indicate tension (T) orcompression (C).1.6in2.ins. OCE = 9260 psi (T); ODE = 22.2 ksi (T); O DF18.5 ksi (C)%3D%3DD6 ftBF8 ft8 ft8 ft6 ft30 kips36 kipsCFigure P-111

GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND STRESS IN GIVEN MEMBER

Answered: 111. For the truss shown in Fig. P-111,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

what is the answer on this problem number 105?
PROB. 1. For the truss shown in Fig. 1, Calculate the stresses in members CE, DE and DF. The cross-sectional area of each member is 1500 mm² A 2.0 M B с 1.5M 4⁰0 KN Fig. 1, 2.0 m E (1) IS M D 2.0 m 50 KN F
A double-decker train. EXERCISES 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the diameter of the connecting rod at its thinnest part, if the permissible tensile stress is 35 N/mm. [Ans. 50 mm) 2. The maximum tension in the lower link of a Porter governor is 580 N and the maximum stress in the link is 30 Nimm. If the link is of circular cross-section, determine its diameter. (Ans. 5 mm) Тор Contents Simple Stresses in Machine Parts 117 3. A wrought iron rod is under a compressive load of 350 KN. If the permissible stress for the material is 52.5 Nimm, cakculate the diameter of the rod. JAns. 95 mm) 4. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if the stress in the wire is not to exceed 100 N/mm. (Ans. 8 mm) 5. A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6 bolts. Calculate the diameter of the bolt if the maximum stress in the tie bar is…
2. Given: Two-dimensional truss structure as shown. (All joints are pin joints.) 65 lbs Fixed Point, Pin-Joint 9 in. 12 in. 60 lbs Material: Steel, diameter 1/2 in. Find: (a) Displacements of the nodes. (b) Normal stresses developed in the members. 45 lbs Fixed Point. Pin-Joint
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed Please do problem 1
PLEASE ANSWER NUMBER 6.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Homework 3 m 13: Find the stresses in members BC, BD, and CF for the truss 3 m C 4 m hown in Fig. Indicate the tension or compression. The cross ectional area of each member is 1600 mm'. 60 kN 90 kN 4 m Figure P-113
Please do it typed not handwriting. Make sure the answer is correct Don’t copy from any other online answers please
Write application software program to find the shortest length of aluminium tubes 50 mm O.D. x 45 mm I.D. with minimum induced stresses to be used in a two-bar truss. The two tubes are hinged to supports that are 2 m apart, as illustrated below. Stress in the tubes should be kept below the yield strength of the material at 320 MPa. 2 m 200 Kg
PROBLEM 2 Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 50 kN 30 kN B MATHalino.com 5 m 4 m 4 m 4 m 3 m
Figure 2: Given the below determine the bar force at BD. (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 2) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
Problem 4 A glass sphere with a 30 mm diameter is pressed against a flat carbon steel plate with a force of 5 N. Assume. For glass: E = 46.2 GPa, -0.245 and for steel E, 207 GPa, (a) Determine the radius of the contact surface. -0.292 (4 (b) Determine the maximum pressure at the contact surface. (4 (c) Calculate the principal stresses d., and a, in the glass sphere at the depth=0.037 mm. (d) Maximum shear stress in the glass sphere at the depth: 0.037 mm. (t (4 (e) Draw the Mohr circles for the stresses and show the point corresponding to the maximum shear stress. (3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS