11.For the following industrial device consisting of a mass isolated from its fixtures by two rubber dampers and a offset spring provide an estimate of the system's damped natural frequency in the vertical direction. Assume the rubber dampers ądd damping and only negligible stiffness to the system and that the spring is long enough such that the angles remain constant. rubber damper

11.For the following industrial device consisting of a mass isolated from its fixtures by two rubber dampers and a offset spring provide an estimate of the system's damped natural frequency in the vertical direction. Assume the rubber dampers ądd damping and only negligible stiffness to the system and that the spring is long enough such that the angles remain constant. rubber damper

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.4 (a) An electric motor of mass 50 kg is suspended from a support structure on a four-spring system. The springs are arranged in series, with the four stiffnesses being 15 kN/m, 25 kN/m, 30 kN/m and 40 kN/m respectively. Viscous damping is present within the system and the damping ratio is 0.175. i) Produce a neat sketch of the system and state its equation of motion. ii) Determine the level of the viscous damping in the system. iii) Determine the amplitude of vibration of the motor 10 cycles after it is released from an initial displacement of 125 mm.
Title Plot the solution of a linear, spring and mass system with frequency ?n = 3 rad/s, x0 = 1.2mm and v0 Description Plot the solution of a linear, spring and mass system with frequency ωn = 3 rad/s, x0 = 1.2mm and v0 = 2.34mm/s, for at least two periods. Compute the natural frequency and plot the solution of a spring-mass system with mass of 2 kg and stiffness of 4 N/m, and initial conditions of x0 = 1mm and v0 = 0mm/s, for at least two periods.
The amplitude of vibration of a single degree of freedom spring-mass-damper system is observed to reduce to 15 % of its initial value after 5 cycles. Spring stiffness equals (1500 + 007) N/m and mass equals (7.5 + 007) kg. Determine: The undamped natural frequency; The damped natural frequency; The logarithmic decrement; The damping ratio; and The coefficient of damping.
Can you please show the complete solution of the image below. Thanks! Subject: Mechanical Vibration
The following data is given for the spring-mass-damper system shown in Figure 1: • K1 = 250 N/m, K2 = 350 N/m • C1 = 150 N/ (m/sec), C2 = 200 N/ (m/sec) • m = 41 kg Detemine i. The undamped natural frequency. ii. The damping ratio. iii. The damped natural frequency. Response of the system x (t) for given initial conditions: X0 = 0.005 m and vo = 5 m/sec. iv. x(t) k 1 k 2 mow m C1 C2 Figure 1
2. Calculate the natural frequency and damping ratio for the system in figure below given the values m = 10 kg, c = 100 kg/s, k₁ 4000 N/m, k2 200 N/m, and k3 1000 N/m. = Assume that no friction acts on the rollers. Is the system overdamped, critically damped, or underdamped? C кий m k₂ k3
A mass-spring damper system has the following parameters: • mass 250g damping constant 1/36000 Nh/m • spring stiffness 500 N/m Calculate the damped frequency. O 1.55.2 rad/s O 2.25.8 rad/s O 3. Not possible to calculate. O 4.79.4 rad/s O 5.44.7 rad/s
What is true option
Project 7: The landing gear of a commercial aircraft is modeled as mass-spring-damper system as shown in figure below. Your role is to define the main characteristics of such motion when the aircraft lands on rough runway that causes an oscillator motion as shown in the Figure.8. Your manger asked you to write a report showing your analysis for the system to avoid any excepted damages to the landing gear. Damper x(t) Suspension System Oscillation Spring Street and Bumps Oscillations Elastic Tire Figure.8: Car's Suspension mass-spring-damper system A. For any mass-spring system, explain the natural frequency of vibration. B. To identify the system main parameters, the following mass-spring-damper model is identified: x(t) = 0.1179e-25.2t sin (50t + 0.3224n) Determine the amplitude and phase angle of the transient response within the system? C. What is the frequency of the runway vibration required to cause resonance? Briefly, explain why it happens. D. Briefly, suggest how to prevent…
5- Please I want solution of all sub-parts by typing. Many Thanks
The following data is given for the spring-mass-damper system shown in Figure 1: • K = 250 N/m, K2 = 350 N/m • C1 = 150 N/ (m/sec), C2 = 200 N/ (m/sec) • m = 47 kg Determine: i. The undamped natural frequency. ii. The damping ratio. The damped natural frequency. Response of the system x (t) for given initial conditions: xo = 0.005 m and vo = 5 m/sec. ii. iv. x(t) k 1 k 2 wom m C1 C2 Figure 1
ENGINEERING VIBRATION QUESTION.An electric fan with a mass of 50 kg is subjected to harmonic excitation due to an unbalanced mass. A spring-damper system was designed to minimize the force transmitted to the bottom of the fan. An attenuator with an attenuation ratio of ζ = 0.2 was used. Calculate the spring stiffness so that the force transmitted to the floor is less than 10% when the fan rotates at 10,000 rpm.how can i solve it..... It's too difficult for me. 6