11.6 Two 15-mm steel plates with S, = 400 MPa are butt-welded using E70 series weld- ing rods and good welding practice. The weld length is 90 mm. What is the maxi- mum tensile load that can be applied to the joint with a safety factor of 3? (See Figure P11.6.) FIGURE P11.6 15 mm F Weld length = 90 mm S,= 400 MPa SF=3 E70 series weld

11.6 Two 15-mm steel plates with S, = 400 MPa are butt-welded using E70 series weld- ing rods and good welding practice. The weld length is 90 mm. What is the maxi- mum tensile load that can be applied to the joint with a safety factor of 3? (See Figure P11.6.) FIGURE P11.6 15 mm F Weld length = 90 mm S,= 400 MPa SF=3 E70 series weld

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m, you decided to apply the concept of simple machine. You want an inclined plane to be built. Given the angle between the incline and the ground, what would be the most efficient incline to be built to raise the equipments? Why? Here are the angles you can choose from for your incline: a. 15°; b. 30°; c. 60°
Question In the image. Please explain with steps to explain how you got the answer.
1. If a rigid body is in translation only, the velocity at points A and B on the rigid body. a. are usually different b. are always the same c. depend on their position d. depend on their relative position
Solve in 15 min
A transmission shaft used to transmit power of 55 kW. During transmission shaft is subjected to a 30 N.m torque. Calculate the number of revolution of the shaft in one minute.
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
Choose correct answer: When the cylinder is cushioned at the end of the stroke, how does cushioning affect the piston's force? At the beginning of the stroke, cushioning increases the piston's force. At the beginning of the stroke, cushioning reduces the piston's force. At the end of the stroke, cushioning increases the piston's force. At the end of the stroke, cushioning reduces the piston's force.
The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston stroke is given as 3.75 inch. Since the compression ratio of this engine is 9.5, find the stroke volume, combustion chamber volume and cylinder volume in cm3.
help! please write the complete solutions. Thumbs-up willl be given! DYNAMICS OF RIGID BODIES! A subway car leaves station A; it gains speed at the rate of 4ft /s2 for 6 s and then at the rate of 6ft /s2 until it has reached the speed of 48 ft/s. The car maintains the same speed until it approaches station B; brakes are then applied, giving the car a constant deceleration and bringing it to a stop in 6 s. The total running time from A to B is 40s. Determine the distance between stations A and B.
The first diagram is wrong, line AB should be longer since its length is equal to 580mm than line P2B which is equal to 360mm, please revise.
In a manufacturing process, a drill press automatically drills a hole into a sheet metal part on a conveyor. In the drilling operation the drill bit starts at rest direcdly above the part, descends quickly, drills a hole, and quickly returns to the start position. The maximum vertical speed of the drill bit is 4 in./s, and while drilling the hole, it must move no more than 2.6 in./s to avoid warping the metal. Let s(t) be the drill biť's height (in inches) above the part as a function of time t in seconds. Sketch possible graphs of the drill bit's velocity [s'(t)] and acceleration [s"(t)].
How many rotations of a 1 m diameter wheel would it take to traverse 50 m of distance.