11. Water at 65 F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe

Q: Solidworks part Units: IPS Material: AISI 1020 Part origin as described in image. Any direction…

A: Material: AISI 1020 Units: IPS   To create: The given part in the Solidworks.

Q: Draw isometric projection of casting, two views (FV and TV) of which are shown in figure in First…

A: Refer the following image for the the required rough sketch of isometric view of the given…

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A: Find , Clearance volume  Swept volume ,

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: I am lost as to where the 2560.89 came into the equation?

A: The preceding method describes how to calculate the time when the centripetal acceleration of a bike…

Q: I just have one question to clarify. The given problem stated that in the part of value of…

A: To find : value of elastic modulus of steel and aluminum Is correctly used in solution or not

Q: For the figure below, all dimensions in inch. A/The total Area:* /The value of Y-bar is: * the value…

A:

Q: The turbine on a ship has a mass of 400 kg and is mounted on bearings A and B as shown. Its center…

A: Determine the vertical reaction at bearings if ship undergoes only rolling motion ω1=0.2 rad/s…

Q: (b) Liquid with a density of 800 kg/m³ flows through the pipe contraction shown in Figure Q1 (b).…

A:

Q: 1. A gas in a cubical container with side equal to 0.3568 m has a pressure of 0.24 MPa at 24°C. If…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: In this task, various ideal gases are considered. If no other information is given, the specific gas…

A: Since we only answer up to 3 subparts so we will answer first 3. Please resubmit the question by…

Q: 20 2 kg 0.3 m 13000 N/m 40.2m- 9 kg 9000 N/m B. Ceq = C/2 • Keg =, Meg = • Solving for on: keq wn =…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

A:

Q: Find the work W done by a force of 3 pounds acting in the direction 45° to the horizontal in moving…

A:

Q: Why when plugging the formula for crossectional it gives a different value than 6650m2. The table…

A:

Q: A.7 Compute I, for the shaded area given that = 25.86 mm.

A:

Q: 1.Total Area: c a. 53.61 m2 b. 88.57 m2 c. 31.43 m2 d. 62.16 m2 2. X: a. 1.97 m b. 8.68 m c. 5.62 m…

A: Please see the attached detailed solution:

Q: ompute the moment of inertia, Ix of the crosS-sectional area about the neutral axis. + 6 in.- 6 in.…

A:

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: In this problem , the condition of Methane, propane & Hexane are given below.

Q: 5. Cross product of AxB with (Sin 0) would produce results equal to....... а. А.В d. A b. AxB c. AB

A: Ans---- AB Because sin is used in x product which gives an area of a parallelogram that is made up…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: In a distribution system, Reservoir A supplies water to a branched system with Reservoir B and…

A: A reservoir is a man-made mechanism for storing water. The majority of reservoirs are created by…

Q: = interest ra

A: i=6.14%

Q: Answer with True or False of the following question: 5. For a fluid at rest, the shear stress is…

A: 5 . For a fluid at rest, the shear stress is zero. True.   When we apply shear stress on solid it…

Q: find the answer A piston-cylinder device provides 8 kJ of work to an external device. 2 kg of air…

A:

Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…

A:

Q: A baseball with a measured radius of 5 inches with a maximum error of 0.01 inches. Find the maximum…

A: Given Data  R= 5 inches  Max error= 0.01 inches  So , R1= 5+0.01 = 5.01 inches

Q: ers of the local police team of Bauan, Batangas recelv call for assistance in towing an abandoned…

A: Given data  Total force on the abandoned car =45kN

Q: 7. 62.4 x 10³ pascals into pound per square inch A. 9.04 B. 9.05 360 slugs into kilogram A. 5,254 B.…

A: 7. Option (B) : 9.05 lb/in2 8. Option (A) : 5,254 kg 9. Option (C) : 0.58474 lb/ft2

Q: Completely solve and box the final answers. Write legibly 5. How much twisting moment in lbf-ft is…

A:

Q: A) The Figure below shows an illustration of a ballistic pendulum that is used for determining the…

A:

Q: Figure 2 ft 4 ft

A: Given Data: Force F→=55i^-40j^+30k^ lb

Q: 4. Evaluate the density of how many tons per cubic yard there is in 3.59 kilograms per cubic meter.…

A: Given   Density = 3.59 kg/m3

Q: 1. A certain ideal gas X has molecular weight of 10 g/mol and specific heat ratio of 2. Initially, X…

A: For solution refer below images.

Q: A small ship capable of making a speed of 6 knots through still water maintains a heading due east…

A: Given data  Velocity of ship =  knots Length of AB = 10 nautical miles Time = 2 hr Find the velocity…

Q: Directions: Use the appropriate equation to recorded below or in your Engineering Design journal.…

A: This question is based on the concept of lever, effort and load.

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.