11. is completed, bypassing the temperature screening and standard operating procedure to enter the venue. The screening system consists of four inputs A, B, C and D and 1 output G. Table Q.11(a): Input and Input UTM UTM IMUTM Sensor/Actuator Function OUTM U Per UTMITM determine whether the visitor has a fever (logic A Thermometer To measure the body temperature of the visitor to UT UTM UTM C B Video camera not. or To detect whether the visitor wears a face mask (logic Gate control high). or not. The control switch can change the gate operation mode to either automatic mode (logic low) or bypass mode (logic high). To detect whether the visitor has completed hand sanitisation (logic high) using the sanitiser dispenser . bypass switch Infrared sensor IM U UTS UU G Auto gate visitor has passed the temperature screening, free and wear a face mask. UTM UTM UTM 8 UT S face mask detection. UTM OUTM/ 8 UTM TMOUTM TM 6 U UTM (b) Implement the logic circuit for the above system using a 4-to-1 multiplexer and basic UTM gates. UTM UIM ITM UTM TM UTM t

11. is completed, bypassing the temperature screening and standard operating procedure to enter the venue. The screening system consists of four inputs A, B, C and D and 1 output G. Table Q.11(a): Input and Input UTM UTM IMUTM Sensor/Actuator Function OUTM U Per UTMITM determine whether the visitor has a fever (logic A Thermometer To measure the body temperature of the visitor to UT UTM UTM C B Video camera not. or To detect whether the visitor wears a face mask (logic Gate control high). or not. The control switch can change the gate operation mode to either automatic mode (logic low) or bypass mode (logic high). To detect whether the visitor has completed hand sanitisation (logic high) using the sanitiser dispenser . bypass switch Infrared sensor IM U UTS UU G Auto gate visitor has passed the temperature screening, free and wear a face mask. UTM UTM UTM 8 UT S face mask detection. UTM OUTM/ 8 UTM TMOUTM TM 6 U UTM (b) Implement the logic circuit for the above system using a 4-to-1 multiplexer and basic UTM gates. UTM UIM ITM UTM TM UTM t

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2 of the internal modules in the 89C52 model microcontroller are given correctly in the following options? a) timer / counter,PWM b) I / O, PWM c) timer / counter, UART D) ADC, PWM e) I / O, ADC
Solve it fast fast plz
i need the answer quickly
A temperature sensor operates in the range of 0 to 80 degree Celsius and it is converted into voltage output between 0 to 8 volt. If the 4 bits ADC is used, then answer the following questions. 1) Draw a quantization map 2) If the temperature is 20 what will be the digital output from ADC, show your computation. 3) If we pass through result from ADC back to DAC what is the temperature value. Show detail computation.
A digital wave is received. It says the value for low is 5 V. The system registers it as low from 8V. This system switches On as of 12 V and registers High at 15 V. What is the unacceptable range of the system?
The 555 timer connected in the monostable multivibrator mode: a) Design the circult to provide an output pulse 60 seconds wide? b) Determine the recovery time? Take: B = 100 RA www Ca :V.(t) V. Ve Discharge Threshold Trigg Gnd Control Reset 555 cutput V₂
Choese correct
Choose the wrong statement for Dual converter (a) Rectifier II produces 2 nd Quadrant parameters(b) Rectifier II produces 1 st Quadrant parameters(c) Rectifier I produces 4 th Quadrant parameters(d) Rectifier I produces 2 nd Quadrant parameters a. (b) and (d) b. (c) and (b) c. (a) and (c) d. (a) and (b)
Write short notes on temperature sensor & explain the characteristics of RTD, Thermocouple and Thermistor with neat sketch
I need the answer quickly
i need the answer quickly
Choose the correct statement for Dual converter (a) Rectifier Il produces 2 nd Quadrant parameters (b) Rectifier Il produces 3 rd Quadrant parameters (c) Rectifier I produces 4 th Quadrant parameters (d) Rectifier I produces 1 st Quadrant parameters O i. all the above O ii. (c) and (b) only O ii. (b) and (d) only O iv. (a) and (b) only A 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz for 14 ohm and 1.5 H load. If the firing V. angle a = 50, then the average output voltage is