Answered: 10N force is uniformly distributed over… | bartleby

Related questions

Question

10N force is uniformly distributed over the surface of a sphere of radius 20cm. The force at each point acts inward along the normal at that point. Find the fractional change in volume if the compressibility of the sphere is 10-11m2/N.

a) 3*10-10

b) 1.5*10-11

c) 1.98*10-10

d) 2*10-11

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Homework 4 Problem 2: A hand-driven tire pump has a piston with a 2.8 cm diameter and a maximum stroke of 24 cm. Part (a) How much work do you do in one stroke if the average gauge pressure is 2.4 × 105 N/m2? W = ______ Part (b) What average force do you exert on the piston, neglecting friction and gravitational force? F = ______
Tire gauges for air pressure as well as most other gauges used in an industrial environment take into account the pressure due to atmosphere on earth that's why your car gauge reads zero before you put it in on your tire to check your pressure this is called gauge pressure. The real pressure with any tire or after or other objects containing pressurized stuff would be a combination of what the gauge reads as well as the atmospheric pressure. If a gauge on a tire reads 26.23 psi what is the real pressure in the tire pascals? The atmospheric pressure is 1.01×10 to the fifth power PA
The bulk modulus of water is B = 2.2 x 10⁹ N/m2. What change in pressure AP (in atmospheres) is required to keep water from expanding when it is heated from 18.8 °C to 30.5 °C? Number i eTextbook and Media Units
9-90. The starter for an electric motor is a full cylinder and has the cross-sectional areas shown. If copper wiring has a density of Peu = 8.90 Mg/m³ and the steel frame has a density of Pst = 7.80 Mg/m³, estimate the total mass of the starter. Neglect the size of the copper wire. Problem 9-90 Steel Copper 80 mm 50 mm 30 mm 100 mm 60 mm
4) The turbine extracts 0 hp from the water flowing through it. The pipe with diameter of 1 ft and length of 300 ft is assumed to have a friction factor of 0 02. Minor losses are negligible. Determine flowrate through the pipe and turbine? Head losses is h₁ = 85 ft ▼ Imad ti EBOOK (1) 1 = 90 ft 300-ft-long, 1-ft-diameter pipe f = 0.02 Turbine (2) Free jet 42 = 0
EXPLANATION MUST BE TYPED-CAN NOT BE HAND-DRAWN OR HAND-WRITTEN.
A light bar AD is suspended from a cable BE and supports a 30-kg block at C. The ends A and D of the bar are in contact with frictionless vertical walls. Determine the reaction at D in N. a =196 mm, b =110 mm, c =80 mm and d = 160 mm
12 of 20 Provide Feedback P Pearson MacBook Pro
Learning Goal: To learn and practice the geometry skills necessary for complex reflection setups. The law of reflection has the very simple form Oreflected, Vincident = where incident is the angle between the normal and the incident ray and reflected is the angle between the normal and the reflected ray. Although the law itself is easy to use, many realistic situations involve successive reflections from multiple surfaces. The law of reflection does not become any more complicated in such cases, but the geometry of the rays does become complicated. Consider the case of light shining onto a mirror, which is attached to another mirror at some angle a, as shown in the figure (Figure 1). In this problem, we will find the angle at which light leaves the arrangement of two mirrors. Figure 1 of 2 > Part A If the light strikes the first mirror at an angle 0₁, what is the reflected angle 02? Express your answer in terms of 0₁. 0₂ = 0₁ Submit Part B Correct Previous Answers Now, find the angle…
Assume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?
Question list ✔ Question 6 ✔Question 7 Question 8 Question 9 Density of water = 1 lb₂ = 1 g/cm³ = 1000 kg/m³ = 62.4 lb/ft³ = 1.94 slug/ft³ Print Done K During processing, a polymer is pumped through the plant. The pump must produce enough power to move the material a height of 10 meters [m] at a volumetric flowrate of 0.2 cubic meters per second [m³/s]. Assume the specific gravity of the polymer is 0.6262. If the pump is 75% efficient, what is the power rating on the pump (input power) to supply the necessary potential energy in units of horsepower [hp]? Click the icon to view the table of common derived units in the Sl system. Click the icon to view the conversion table. Click the icon to view density of water. The power rating is hp. (Round your answer to one dicimal place.) - X ore Info Length 1 m = 3.28 ft 1 km = 0.621 mi 1 in = 2.54 cm 1 mi = 5,280 ft 1 yd = 3 ft Force 1 N = 0.225 lb, Print Power 1 W = 3.412 BTU/h = 0.00134 hp = 14.34 cal/min = 0.7376 ft lb/s Done X More Info…
1. Find kinetic energy per cubic meter of flowing blood (V =1 m') in aorta for individual at Q = 5 liter/min, radius of aorta 1 cm. The density of blood is rest. Suppose flow rate is about p-1.05-10' kg/m. R =

SEE MORE QUESTIONS