- -1025. In a reinforced concrete beam, b = 250 mm, d = 450 mm, 10. The actual maximum stresses developed are f = 6 MPa and f= 120 MPa. Determine the applied bending moment and the and n = . steel area required. Ans. M = 45.0 kN-m; A, = 938 mm² 1036

- -1025. In a reinforced concrete beam, b = 250 mm, d = 450 mm, 10. The actual maximum stresses developed are f = 6 MPa and f= 120 MPa. Determine the applied bending moment and the and n = . steel area required. Ans. M = 45.0 kN-m; A, = 938 mm² 1036

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 – 28 mm deformed…

A: Answer we are given f'c = 49 Mpa fy = 362 Mpa As = 4- 28 mm bars As = 4 * π4*282 As = 2463 mm2 We…

Q: The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: Slab thickness =200mm =0.2mUnit weight of concrete=23.6 KN/m3Live load for office=2.4…

Q: A reinforced concrete rectangular beam is subject to design loads that result in a maximum bending…

A: Answer We are given Maximum bending Moment Mu = 360 kip-ft Maximum beam width b =18 in Reinforcing…

Q: A 380mmx520mm beam is reinforced with 5 diameter 28mm steel bars (one layer). Strength of concrete…

Q: -6 The concrete post (Ec = 30 GPa and a =10x10°c) is reinforced with six steel bars, each of 10 mm…

Q: If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24 mm2.Show

A: Step: 1 Truss: - It is a pin jointed frame where bending moment does not exist in member only carry…

Q: III, The section size and reinforcements of a simply supported reinforced rectangular beam is shown…

Q: Figure shown below, a simply supported beam and the cross-section at midspan. The beam supports a…

Q: A reinforced concrete beam has a width of 300 mm and an effective depth of 450 mm. The beam is…

A: Given: Required : Balanced steel ratio Depth of compression stress block Nominal moment capacity

Q: For the truss shown, the wooden AB bar has solid cireular cross-section with diameter d and the…

A: Given information: Here, P = 75 kN Length of AB, L = 2 m F.O.S, n = 2.5 E = 10 GPa Tetmajer’s…

Q: The column shown is reinforced with 12 steel bars evenly distributed at all faces of the column. The…

A: Solution:- Given data:- No of steel bars = 12 Width(b) = 375 mm depth (d) = 600 mm Yield strength of…

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

Q: 6-126. The wooden section of the beam is reinforced with two steel plates as shown. If the beam is…

Q: A simply supported beam has a width of 310 mm and an effective depth of 330 mm. It is reinforced at…

Q: A simply supported rectangular beam has a width of 300mm and the distance to the centroid of…

Q: tensile-reinforced d=500mm to the center of the bars, which are placed all in one row. If f,=42QMPA…

A: Given, b=300 mm d=500 mm Yield stress of steel fy=420 MPa Characteristic strength of concretefck=35…

Q: 2. Determine the dimension "L" of the hollow pentagonal pedestal shown if it has to carry an ivory…

A: To find the dimension L of the Hollow Pentagon Diameter of the Hollow portion (Deven)= 35 mm…

Q: A reinforce d rectangular beam with width b and effetive depth d has 4.16 mm bars placed on 1layer…

A: Given: b = 532.5mm, d = 877.5mm fy = 420 MPa, fck = 28 MPa L = 6.35 m WD = 36 kN/m, WL = 47.5 kN/m…

Q: A simply supported beam carries a uniformly supported load. It has a span of 8.6 m and an effective…

A: d = 670 mmb = 410 mmL = 8.6 mRebars 6-28 mmStirrups = 12 mmfc = 29.3 MPafy = 414.5 MPaClear cover =…

Q: istance of the section. The p

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional…

Q: normal Ja-25° K → P= AB kN

A: Given data: P=53 KNA=1200 mm2α=25o Calculating normal stress on the plane a-a:…

Q: A 90mm concrete slab is supported by a beam 7.50m clear span and 1.20m on center. Web dimension and…

A: Given:- 90 mm concrete slabClear span=7.5 mDepth=500 mmWidth=300 mmfC'=21 MPaϕ=0.90Factored…

Q: A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The…

Q: A simply supported wood beam with a span of L = 13 ft supports a uniformly distributed load w. The…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

Q: A 6m simply supported beam has a width of 330 mm and an effective depth of 520 mm. The yield…

A: Simply Supported Beam: When the ends of a beam are set to stand freely on supports of the beam, it…

Q: SITUATION 1: A 250 mm wide rectangular concrete beam is reinforced for tension only. The beam has an…

Q: A rectangular reinforced concrete beam with width of 350mm and effective depth of 600mm is subjected…

Q: Find the maximum allowable value of P for the column. The cross sectional areas and limiting stress…

Q: A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 – 28 mm deformed…

A: Given : Width of concrete beam, b = 400 mmNumber of bottom fiber bars, n = 4Diameter of bottom fiber…

Q: 9. The rigid bar ABC is supported by a pin at A L=4 ft and a steel rod at B. A = 0.5 in.2 E= 29 x106…

Q: A simply supported concrete beam 6m long is reinforced with four-28mm diam. tension barss. The beam…

A: L= 6 mTension bars = 4-28 mm diaCompression bars= 2-28 mm diaSteel covering = 70 mmf'c= 30 Mpafy=…

Q: forces in each layer of steel corresponding to the case of tension controlled strain limit.

Q: A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with…

A: Bending stress: It is the stresses generate because of the bending of the beam. Its variation is…

Q: pove the bottom of the beam f. = 35 MP Reinforced indices for the beam Safe ultimate moment capacity…

A: Given:- 300mm x 500mm span=5m f'c=35MPa Aps=1200mm2 To find:- a) Reinforced indices for the beam b)…

Q: A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 - 28 mm deformed…

A: f'c = 49 Mpafy = 362 MpaAs = 4- 28 mm bars As = 4 * As = 2463 mm2 We need to calculate the depth of…

Q: it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the…

Q: A rectangular beam which is limited to 350 mm by 650 mm is reinforced at the compression side with…

A: Given data: b=350 mmD=650 mmAS'=1000 mm2AS=4000 mm2d'=50 mmc=127.84 mmfC'=35 MPaβ=0.81fy=400…

Q: Q3 h nɔd. For the truss shown, the wooden AB bar has solid circular cross-section with diameter d…

A: Given that; L=2m P=75KN n=2.5 E=10GPa λ<λcr=100, d=?Tetmayer's Formula;σcr=(28.73-0.19d)MPa

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: The values given in the question are as follows: Width of beam(b)=310 mm Effective depth of…

Q: Design Problem 4 The pretensioned rectangular beam shown in Figure 4.0 has straight cables with…

Q: The steel framework is used to support the 4-in. reinforced lightweight concrete slab (unit weight =…

Q: "Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Question

-
-1025. In a reinforced concrete beam, b = 250 mm, d = 450 mm, .
10. The actual maximum stresses developed are f = 6 MPa
and f= 120 MPa. Determine the applied bending moment and the
and n =
steel area required.
Ans. M = 45.0 kN-m; A, = 938 mm²
1035 C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

The given beam is:

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A reinforced beam has a: width = 500 mm effective depth = 600 mm n = 9 If the maximum stress of 5 MPa is developed in the concrete when resisting a moment of 80 kN-m. What stress is developed in the steel. What area of reinforcing steel is required?
A timber beam having a simple span of 15m carries a total load including its own weight of 25KN/m. It has a width of 200 mm and a depth of 250mm. The wooden section is made up of 80% Apitong.Fb = 17.5 MPaEw = 7510 MPaFv = 1.85Mpaa. Determine the maximum flexural stress of the beam.b. Determine the maximum shearing stress of the beam.c. Determine the maximum deflection of the beam.
An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2. If the average normal stress in the steel column must not exceed 140 MPa, determine the minimum required dimension “a” so that the bearing stress between the base plate and the concrete slab does not exceed 11 MPa.
A rectangular beam which is limited to 350 mm by 650 mm is reinforced at the compression side with As’ = 1,000 mm2and on the tension side As = 4,000 mm2. The beam has an effective depth of 510 mm and its neutral axis is located at 127.84 mm below the top of the beam. Assume steel in tension yields but that in compression does not yield. F’c = 35 MPa, β = 0.81, fy = 400 MPa. Steel covering on top is 50 mm. Determine stress of steel in compression. Determine the depth of compression stress block. Determine the moment capacity of the beam.
A reinforced concrete beam having a width of 300mm and a overall depth of 600 mm is reinforced with 2-25mm compression bars placed 60 mm from extreme concrete & 6-25mm tension bars with concrete covering of 60 mm from the centroid of the bar group. Concrete Strength, fc' = 27 MPa, Steel Strength, fy = 415 MPa. A. Determine the balanced steel area considering the contribution of the compression steel. B. Determine the maximum tension steel area allowed by the code.
A 62.6-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used oy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. B D 1.5 m The smallest allowable dimension dis mm.
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moment. Fc'= 40 Mpa.
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying a moment of 100 kN.m. Find the total compressive force in the concrete. Use n = 9.
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
need answers pls and solutions asap, thank you!