100 mm width and 250 mm depth rectangular beam shown in Fig. 2. Is subjected to a maximum shear force of 50 kN. Determine: I Average shear stress II. Maximum shear stress III. Shear stress at 25 mm above the neutral axis

Q: What is adsorption zone?

A: The deposition of molecular species onto the surface of any object is known as adsorption. The…

Q: Please recalculate and maksure everything above is correct. thanks

A: Steps to solve this question:Assumptions and sign conventions of forces and reactions.Find the…

Q: How to Install the Gypsm Board.

A: Gypsum Board: Gypsum boards or Plasterboards are one of the latest trends in the construction…

Q: What is a plumbing tape?

A: Let us analyse the question ( Plumbing tape ) in step 2.

Q: List several locations where flashing is required?

A: flashing  - flashing use as a obstacle for water penetration. it is thin impervious layer on the…

Q: what is piping system?

A:

Q: You have decided to build a deck on your new home 12 feet wide x 16 feet long, using the standard 2…

A:

Q: Which one of the following is the most economical store design? a. Geometrical layout b. Angular…

A: the correct answer is option c - straight floor layout

Q: 2000 MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0.000 0.020 0.040 0.060 0.080 Strain Stress…

A: Considering the given stress- strain graph the solutions are provided in the following steps-

Q: Draw and label the standard symbols used in a horizontal stadia sight. Define each symbol used.

A:

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: Types and parts related to Plumbing System

A: Given data :-  As given the question asked for plumbing sytem and types and parts:-   Types of the…

Q: Please answer LETTER "B" AND "C". UPVOTE WILL BE GIVEN!

A:

Q: Define emission factor?

A: Emission Factor An emission factor is a representative value that attempts to relate the quantity of…

Q: SANITARY SEWER SYSTEM

A: To draw the city sanitary sewer system

Q: Define Bucket augers

A: Unconsolidated Soil: If the soil has not reached the equilibrium under the applied overburden loads,…

Q: Where are fire flame detectors used?

A: Answer Introduction Fir flame detector is the sensor that is used to detect the fire flame in any…

Q: Q#9: Explain different methods of Plane Tabling.

A: There are four methods to perform plane table surveying. a) Radiation - 1)It is the method of…

Q: A Totalstation encompasses: Spirit Level Theodolite EDM

A: Total station encompasses?

Q: What is pole placement method

A: Answer:- The pole placement approach is a very useful design tool, particularly for estimating the…

Q: How do you think are the details for cut bars and anchorages determined? Answer in 3-4 sentences…

A: Anchorage: The reinforcement bars are provided in the type of hooks and bends. The anchorage bars…

Q: Assignment #5: 1. Locate the centroid of the shaded area as shown below. 12 6 6"

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: What are canopy restrictions?

A: Canopy:

Q: How many satellites in a full GPS constellation? O 30 O 12 O24 O 18

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Is there anything special about a CPLD

A: Several different types of the PLDs which means programmable logic devices are existed such as FPGA,…

Q: Flowchart of how to estimate EARTHQUAKE LOADS. Please write it down, don't use the book nscp.…

A: Analysis of past earthquakes aids in understanding their causes and mechanisms and may even aid in…

Q: Q#11: Define the following terms: i. Elevation ii. Bench Mark iii. Back Sight iv. Fore Sight v.…

A:

Q: Line P to Q intersects the street alignment as shown in the sketch below. What is the length of line…

A:

Q: 2. A load P is supported by two steel springs arranged in series as shown. The upper spring has 20…

A:

Q: 2. Explain the difference between the TRIM default option and TRIM double enter. O Enter your answer

A: Trim default: This tool is simple to use. We need to just select the object which needs to be…

Q: top view drawing

A: In top view we see the object from top. Here dotted line represents a cut inside the object.

Q: Please write a report about (Setting out Right angles) by using tape. Introduction Procedure Aim…

A: Setting out Right Angles: Introduction: While setting out a building plan, it is usually made up of…

Q: What is Auger boring ?

A: given question is from geotechnical engineering related to the topic soil exploration and…

Q: Q25. Draw the plan, section and elevation of the given line diagram. BАTH 2000 x 2500 BED 5000 x…

A:

Q: Define Shotcrete.

A: In a block of conventional concrete, the concrete is placed, and then it is compacted. But in…

Q: trols the design of stairways? he maximum height and the minimum height of a stair riser according…

A: 1) what controls the design of stairways Stairway design is typically controlled by building codes…

Q: PLEASE ENCIRCLE THE PART WHERE HAZARD COULD OCCUR

A: Hazards are the risk or the possibility of danger at a place by any means of accident. There are…

Q: Why compass box is covered with glass?

A: compass box is a box which contains magnetic needle.  A needle is pivoted inside the box which can…

Q: Based on the attached enlarged floor plan, how many sq. m. of 16mm (5/8") plywood backing is…

A: Grab bars are graspable bars to help maintain balance and lessen fatigue while standing. They are…

Q: Which shortcut key lets you zoom the drawing area?

A: Of the given options, the shortcut key to zoom the drawing area in AutoCAD has to be found out

Q: Create the sequence of how to create the objects on the image. Standard FIV Standard Find tet Use…

A: To Determine The steps in sequence to create the objects on the image given in the question.

Q: Determine the number of linear feet needed for the shoe and double top plates for the building plans…

A: For plan 1   Total area of wall = (53 x 30) = 1590 ft2  For one shack and double top plates…

Q: write full detailed and full explain on question neat and clean plzzz. Explain some situations in…

A: Hoisting is really the raising of materials against gravity using a variety of apparatus ranging…

Q: What is specific gravity (sp gr)

A: Given data in question  Specific gravity  To be discussed  What is specific gravity    Specific…