Please answer thanks 100 mHiL200 N5 Vvo(t)80022. The above circuit is a simplified boost converter used to generate output voltages higherthan the input voltage (5V in this case). The switch is closed for t<0 and opens at t=0.Assume an ideal diode.a. Determine the state of the diodeb. Determine an expression for and sketch vo(t)c. Verify your assumption on the state of the diode (Tip: if your initial guessdid not pass the verification, flip your assumption and repeat the above steps)

Answered: Image /qna-images/answer/1ea3df08-89e7-4f60-9603-64d661979848.jpg

Answered: 100 mH iL 200 N + 5 V vo(t) 800 2 2.…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Four diodes and one Zener diode are connected to form the circuit below. a) Describe how a single diode behaves when forward biased. 5) draw the output as the input changes from -12 V to +12 V. Assume that all diodes can be represented by a constant-voltage of 0.6 V (in forward bias) and the Zener diode has a breakdown voltage of 6.8 V. d) What is the function of the circuit? Suggest a proper application. I kN Da Dr
Choice the correct answer
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Demonstrate clipping of negative waves with an inverted diode in the output.A circuit which removes the peak of a waveform is known as a clipper. Show a negativeProduce a schematic diagram.During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diodedoes not conduct. It is as if the diode were not there. Show the positive half cycle isunchanged at the output V(2). Show the output positive peaks overlays the input sinewaveV(1).Voltage values: Resistor valuse: 1 K ΩDC offset: 0 VAmplitude: 5 VFreq: 1 KHz
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
Solve...
quick reply needed.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS