100 ft-lb at joint B -10 ft- 50 Ib 100 Ib A B 20 ft 10 ft Pin connection

Q: 4. A cantilever beam AB of length L=12 m is subjected to a concentrated load P = 35 kN and a couple…

A:

Q: An overhanging beam ABC has a guidedsupport at A, a rectangular cross section, and supportsan upward…

A:

Q: A rectangular bar of length L has a slot inthe middle half of its length (see figure). The bar…

A: Given Data The axial stress acting in the middle region is: σ=160 MPa The length is: L=750 mm The…

Q: Figure Q6 shows the cantilevered 6061-T6 aluminum alloy rectangular beam fixed at A. Given Modulus…

A:

Q: Two flat beams AB and CD, lying in horizontalplanes, cross at right angles and jointly supporta…

A: Given data as per question The load applied =P  deflection at AB is δAB=(P2)LAB348EIABdeflection at…

Q: A simply supported wide-flange beam ofspan length L carries a vertical concentrated load Pacting…

A: Given Beam = W250 X 44.8 L = 3.5 m Angle = 26.57 P = 18 kN To find Magnitude of beta Maximum stress…

Q: OC will be 0.05 m

A: (a) Draw a free-body diagram of the system.     Apply force equilibrium in a horizontal direction.…

Q: An aluminum box column with a squarecross section is fixed at the base and free at the top(see…

A: Given data as per question force P = 50 kN  E =73 GPa  The thickness of the wall = 8 mm Calculations…

Q: A bracket ABCD having a hollow circularcross section consists of a vertical arm AB (L 5 6 ft),a…

A:

Q: A prismatic bar AB with a solid circularcross section (diameter d) is loaded by a distributedtorque…

A:

Q: Calculate: a) the vertical support reaction in support A. When sketching FBD, set the positive…

A:

Q: A PB y Pc W1 В W2 H A B C L1 L2

A:

Q: A simply supported beam ABC is loaded at theend of a bracket BDE (see figure). Draw…

A: Draw the free-body diagram of beam ABC.

Q: A long slender column ABC is pinned atends A and C and compressed by an axial force P(see figure).…

A: Give Data The modulus of elasticity is: E=200 GPa The distance between the lateral support is: L =…

Q: In the figure, one end of a uniform beam of weight 150 N is hinged to a wall; the other end is…

A:

Q: 4.3-20 A space truss is supported at O, A, D, and C (see figure). Loads P are applied in the y…

A:

Q: A floor system in a small building consistsof wood planks supported by 2-in. (nominal width)joists…

A: Given Length,  L = 10.5 ft = 126 in.            w = floor load               = 120 lb/ft2 = 0.8333…

Q: A curved frame ABC is fixed at one end and subjected to a concentrated load P, as shown in Figure.…

A:

Q: 6.5kN Find the force in EF,CF,BC and mention if it's a compression or

A:

Q: Q2/ A beam (ABC) is supported at A&B and carries a uniformly distributed loads between AB of 50N/m…

A: Here we will apply equilibrium conditions

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

A:

Q: A curved frame ABC is fixed at one end and subjected to a concentrated load P, as shown in Figure.…

A: →For section AB(0≤x≤L):-Mx=PxMx=0=MA=0Mx=L=MB=PL →For section BC:- Equation of moment at an angle…

Q: A plane frame with pin supports at A and Ehas a cable attached at C, which runs over a…

A: a.Free body diagram:   No horizontal force on frame,henceEx=0Now,Ey+Ay=500lb⇒Ey=500lb-AyNow,Net…

Q: A steel wire (E = 200 GPa) of a diameterd = 1.25 mm is bent around a pulley of a radiusR0 = 500 mm…

A: Simple stress is often called direct stress because it develops under direct loading conditions,…

Q: A cantilever steel beam with the triangular cross section is loaded with the concentrated force as…

A:

Q: * For the cantilever beam shown. find the value of Normal stress due to :axial load at point C 4 KN…

A:

Q: A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 165 kN, acting as…

A:

Q: Question 1: Two uniform beams are attached to a wall with hinges A, B, and then hinged together at C…

A:

Q: A long, slender bar in the shape of a rightcircular cone with length L and base diameter dhangs…

A: Given   Ny = axial force acting on element dy   Ay = cross-sectional area at element dy  AB =…

Q: A pulley 1.2 m in diameter and supporting a load of 900 N is mounted at B on a horizontal beam…

A:

Q: Determine the maximum tensile stress o, and maximum compressive stress o. due to the concentrated…

A: SolutionGiven dataP=8 KNL=3 mC=1.1mb=75 mmb1=25 mmh=100 mmh1=75 mm…

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E = 200…

A:

Q: Applied mechanics: An undersea research vehicle has a spherical hull of 1m radius and a 40mm…

A: Radius r = 1m Thickness = 40mm High strength alloy steel  yield point =700MPa Relative density of…

Q: A simply supported span (middle span) of 6-m length with double cantilever of 1.5 m at each end  is…

A: **According to the guidelines we can answer only three subparts, please repost the question to the…

Q: A 1000 N uniform beam at angle α = 60.0° with respect to horizontal is supported by a cable at angle…

A: Given Data: The weight of the beam is W1 = 1000 N. The weight of the mass is W2 = 1500 N. The…

Q: Q3/ A simply supported beam of weight 20KN/m is supported at A&B, AB= 5m. Two-point loads of (W)KN &…

A:

Q: The horizontal rigid beam ABCD is supportedby vertical bars BE and CF and is loaded byvertical…

A: Given             E = 200 GPa Area, ABE= 11,100 mm2        ACF = 9280 mm2. Find   Deflections

Q: Wo B H L

A: To determine the reactions at A and B

Q: The continuous frame ABC has a fixedsupport at A, a roller support at C, and a rigidcorner…

A: Given Structure under loading To find Frame reaction Maximum moment

Q: (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At…

A: for solution refer below images.

Q: Segments AB and BC of beam ABC arepin connected a small distance tothe right ofjoint B (sec figure).…

A: Strength Of Material

Q: Find the support reactions?

A: Draw the force diagram

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.