100 A 220 V 50 Hz 0.138 H f(x) = 0 90 ohm Solver Configuration Electrical Reference

Q: 6. What is the effect of load inductance on the ripple current? 7. effect of chonnine

A: Effects of load Inductance on ripple current :

Q: The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is…

A: First write the expression for given output voltage waveform and than evaluate the rms value of the…

Q: Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and…

A: In this question we will write relation between voltage and current and power factor ....Also find…

Q: The load voltage waveform of a single phase full bridge inverter supplied fr source is shown in…

A: Rectifier: Because nearly every electrical appliance runs on DC (Direct Current), the rectifier…

Q: 4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive…

A: Given  A circuit of zero lagging power factor  Power factor is defined as the cosine of angle…

Q: ← Voltage and power factor c... A 4 pole 50Hz 100 MVA Turbogenerator has 2 a moment of inertia of 8…

A: Given- 4 pole 50 Hz, 100 MVA turbogenerator, MOI- I=8×103 kg-m2, To Find- The value of 'in'…

Q: + R₁ 44444 R₂ MAMMA ми R5 или M R4 R6₂ AMA R7 www Rq www R8

A:

Q: find total equivalent resistance and reactance and total impedance transferred in primary side.

A: Given transformer circuit is - Given value of turn ratio is -

Q: Let v,(t) = 9cos(2t)V, R1 = 3N, R2 = 82, C1 = 600mF and C2 = 900m F. %3D %3D %3D %3D | + C2 Vs 2i,…

A:

Q: The pu impedance of a circuit element is 0.15. If the base kV and base MVA are halved. Then the new…

A: Given, Per unit impedance of a circuit element, Zpuold=0.15. New kV values, KVnew=12KVold. New MVA,…

Q: x(t) = 7cos (20t + 픔), 2

A:

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given: Load-1:P1=950Wcosϕ1=0.5 LaggingLoad-2:P2=1.14Wcosϕ2=1Load-3:P3=760Wcosϕ3=0.5 leadingline…

Q: a-Find the RMS values of the load voltage and the load current b-Calculate and draw the voltage…

A:

Q: a) Determine the voltage across XC (with VDR). b) Determine total current. c) Determine the voltages…

A: We are authorized to answer only 3 subparts at a time since you have not mentioned which part you…

Q: A voltage and current applied to a single phase load is  v= 26 cos (300t+35)  and i= 19 cos (250t-…

A: Given: v=25cos300t+35°i=19cos250t-20°

Q: Use the information below to answer questions 24 un The voltage across and the current through a…

A:

Q: Two impedances consist of resistance of (15 ohms and series connected inductance of 0.04 henry) and…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 15. You are working on a power factor correction installation, and you notice with a clip-on ammeter…

A:

Q: A 25-ohm resistor connected in series with a coil of 50-ohm resistance and 150-mH inductance. What…

A:

Q: 1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c…

A: we have to calculate capacitance.

Q: A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many…

A: Impedance

Q: Explain in details the relation between phase and line voltages and currents in a star- connected…

A: Circuit diagram for star connected network is given by, Here N is the neutral point R is red phase…

Q: A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power…

A: The power factor for series RL circuit can be written as, p.f=cosθwhere…

Q: what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms

A: The solution can be achieved as follows.

Q: Reactive Power Compensation Regulation, capacitive reactive power should not exceed what percent of…

A: Reactive Power Compensation  Since the major load in power systems is an inductive load that…

Q: An inductive impedance and a resistance is connected in series with a 220V ac source. The power…

A: Given that VS=220V PF=0.94  Fig: R-L circuit  It the RL series circuit magnitude of source…

Q: A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load…

A:

Q: Three impedances, Z1 =1000•Q, Z2 =63.2518.43.2 and Z3 =1002-90•Q are connected in star. Convert the…

A:

Q: Problem 2: Question 2. Consider the three phase generator below: Phase A Phase B N Phase C N N a) If…

A:

Q: Jessica is observing two series connected loads each having a 100 ohms impedance. Jessica Enows that…

A: Kirchhoff's voltage law: It states that in any closed circuit or loop, the total voltage around the…

Q: Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a…

A: In this question,  We need to choose the correct options What is power factor of the circuit.  We…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given data:Load - 1 :P1=950Wcosϕ1=0.5 Lagging Load-2:P2=1.14Wcosϕ2=1 Load-3:P3=760Wcosϕ3=0.5…

Q: How to solve for a (+) Phase Sequence and (-) Phase Sequence? Give an example and explain the steps.

A: When a unsymmetrical fault occurs in the system then system becomes unbalanced. To understand the…

Q: What is the average power in ghe single phase ac circuit with the purely resistive load? It is…

A: According to the Ohm’s law:

Q: inductive impedance made up of a resistor and an inductor has the characteristic that its current…

A: In this question , we will write current and voltage lag lead relation in inductive circuit...

Q: A source delivers 50 kVA to a load with a power factor of 75 percent leading. Find the load’s…

A: average power P = apparent power S  × power factor cos ∅ .  reactive power Q = apparent power S  ×…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given data:Load -1 :P1=950Wcosϕ1=0.5 Load-2:P2=1.14Wcosϕ2=1 Load-3:P3=760Wcosϕ3=0.5 line voltage,…

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.