10.)A ladder, whose length is 10 m and whose mass is 40 kg rests against a frictionless vertical wall. Its upper end is a distance of 7.7 m above the ground. The center of mass of the ladder is 3 1 of the way up the ladder. The coefficient of static friction between the ladder and the ground is 0.53. If a carpenter climbs 85% of the way up the ladder before it starts to slip, find the mass of the carpenter. Show the Free body diagram of your work. Write it on the paper and do not type it

10.)A ladder, whose length is 10 m and whose mass is 40 kg rests against a frictionless vertical wall. Its upper end is a distance of 7.7 m above the ground. The center of mass of the ladder is 3 1 of the way up the ladder. The coefficient of static friction between the ladder and the ground is 0.53. If a carpenter climbs 85% of the way up the ladder before it starts to slip, find the mass of the carpenter. Show the Free body diagram of your work. Write it on the paper and do not type it

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve this question in hand writting step by step
SOM 1. Show your complete solution. ( I know the answers but I need the detailed solution) Given answers: Axial Force A = 7366.667 N Axial Force B = 5666.667 N Axial Force C = 3966.667 N
Solve using paper:Problem 14. Determine the magnitude of M if the resultant of the forces and couple M passes through point O.
A thin plate with a size of 20 cm x 20 cm, with a constant speed of 1.0 m/S between two walls and F it is drawn in the direction in which it is seen in the figure with its force. The distance between the walls is 3.6 mm, and the wall at the top is fixed, and the wall at the bottom is on the left side it is moving at accurate 0.3 M /s constant speed. Fluid viscosity between walls 0.027 Pa.sn and since the velocity distribution is linear (linear) ; a) draw the speed distribution profile, determine where the speed is "0". b) calculate the "F" force that will pull the plate at a constant speed of 1.0 m/s. Fixed Wall = I mm V= 1 m/s F h2 = 2.6 mmi V. = 0.3 m / s Movable Wall
Find the magnitude and direction of the horizontal and vertical components of the hydrostatic force acting on the two-dimensional curved metal surface per foot wide. Calculate the location of the horizontal component of the hydrostatic force.
how to solve this one?
Consider the figure below, depicting a simple beam AB supporting two equal concentrated loads P. A horizontal beam A B of length L is supported by a fixed support at its left end A and a horizontal roller support at its right end B. A point load P acts downwards at a distance a to the right of A and another point load P acts downward at a distance a to the left of B. *Inserted Photo* (Use the deformation sign convention. When entering expressions, use the following as necessary: P, L, and a.)
Verify the given moment(s) of inertia and find and y. Assume that each lamina has a density of p = 1 gram per square centimeter. (These regions are common shapes used in engineering.) = y= Right triangle b 4₁=1 bh³ 1₁ = 1/2b³h
A cross sectional area was generated for a bridge beam support 0.6 y-**- 0.5 0.4 0.3 0.2 0.1 0.1 0.2 0.3 0.4 0.5 0.7 0.8 1.1 1.2 0.6 1.3 -0.1 The formula is given utilized to form the cross – sectional model. Taking the area generated above the x-axis, where A = 8398.
The two mooring cables exert forces on the stern of a ship as shown. Represent each force as a cartesian vector and determine the magnitude and coordinate direction angles of the resultant.
Example: Determine the magnitude and direction of the components of the force 500 N shown in the figure in directions x, y and z. Solution 500 N 65 61 40 y