10.8. For the LTI system, the input signal is x[n], the output signal is y[n], and the impulse response is h[n]. For each of the cases that follow, find the output y[n]. The referenced signals are given in Figure P10.8. (a) x[n] in (a), h[n] in (b) (b) x[n] in (a), h[n] in (c) (c) x[n] in (a), h[n] in (d) (d) in (b), in (c) (e) x[n] in (b), h[n] in (f) x[n] h[n] ... -1 0 1 2 3 (b) 10 1 2 3 4 5 n (a) 1.5 10.5 -10 1 2 3 ... -10 (d) (e) ... ... -1 0 2 (e) (f) Figure P10.8

10.8. For the LTI system, the input signal is x[n], the output signal is y[n], and the impulse response is h[n]. For each of the cases that follow, find the output y[n]. The referenced signals are given in Figure P10.8. (a) x[n] in (a), h[n] in (b) (b) x[n] in (a), h[n] in (c) (c) x[n] in (a), h[n] in (d) (d) in (b), in (c) (e) x[n] in (b), h[n] in (f) x[n] h[n] ... -1 0 1 2 3 (b) 10 1 2 3 4 5 n (a) 1.5 10.5 -10 1 2 3 ... -10 (d) (e) ... ... -1 0 2 (e) (f) Figure P10.8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Circuit needed for this
1
The partial gain for Vg is -2 ±10% R2 = 1kΩ. R1 = 10kΩ Rf = 2kΩ. Record the amplitude of the signal source (vg), the ac component of the output (vout), and the dc component of the output (VOUT) in Table 3. Test to see whether you have met your design criteria. The measurements that you made in Table 3 should assist you in this. Show the results of your comparisons in Table 4.
A radio receiver consists of a Low noise amplifier (LNA), a mixer and an IF amplifier in cascade. The LNA has a power gain of Ap1=134 , the mixer has a gain of Ap2=0.75 and the IF amplifier has a gain of Ap3=8345. If the input power is Pin =0.62mW 1) Find the overall gain as ratio Ar and Ar(dB) ( 2) Find the outputs P, (from LNA), P2 (from mixer) and Pout (from IF amplifier) (unit is mW) (6 3) Express P1, P2 and Pout in dBm ( P1 P2 IF amplifier Арз Pin LNA Мixer out Ap1 Ap2
Use a bistable multivibrator circuit, design a circuit that produces symmetrical triangular and rectangular waveforms of 5kHz Frequency. The op-amps saturate at +8V. The triangular waveform is required to have 4V peak to peak voltage.
Consider an amplifier of this output-input characteristics: Vo = C₁ V₁ + C₂ V2 + ...... Assume these inputs: fA(t) = a cos wдt fB(t) = b cos WBt Also assume: C₁ = 0 Cn for n > 3 Find the following: a. The level of the 2nd & 3rd harmonics relative to the fundamental if only one input is used. b. Repeat if the sum of two inputs is used. c. Repeat if the difference of two inputs is used. For b & c the amplitudes of both inputs are the same.
Consider a boost converter that supplies a resistive load with 32
Note : Value of K1 = 17; K2 = 49 Question : a) Find V1,V2 and V0. b)Draw the output waveform of V1,V2 and V0. c)Draw the transfer characteristics of V0 vs V1. d) Compare T+,T-. Note:: In the below i have add the question and also add 2 answers of the questions. Now you have to identify,which ans is correct and ans if any part is missing.
Find the gain and Rf as it is stated in the picture.
I need the answer quickly
A boost converter is a dc-to-dc switched power supply in which the voltage output is larger than the voltage input. A block diagram for a peak current mode controlled converter is shown below. Find the transfer function Vo(s)/V/(s). Tja(s) Tpa(s) Kf Fm R₁ Tp.(s) K₁ H.(s) Tma(s)
Electronics