VASSESSMENT PROBLEMObjective 2-Understand the condition for maximum real power delivered to a load in an ac circuit10.7 The source current in the circuit shown is3.6 mH3 cos 5000t A.a) What impedance should be connectedacross terminals a,b for maximum averagepower transfer?b) What is the average power transferred tothe impedance in (a)?c) Assume that the load is restricted to pureresistance. What size resistor connected$2005 µF4ΩAnswer: (a) 20 – j10 N;(b) 18 W;across a,b will result in the maximum aver-(c) 22.36 N;age power transferred?(d) 17.00 W.d) What is the average power transferred tothe resistor in (c)?NOTE: Also try Chapter Problems 10.41, 10.48, and 10.62.

Answered: Image /qna-images/answer/498bf9e7-f356-430a-ad30-e889144b3bba.jpg

Answered: 10.7 The source current in the circuit…

10.7 The source current in the circuit shown is 3.6 mH 3 cos 5000t A. a) What impedance should be connected across terminals a,b for maximum average 20 N power transfer?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Please answer alll subparts for like either dislike...
qqqqqqqqqqqq111111111111 bbbbbbbb
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
Q2: Write a lecture for teaching the complex power fed to an (R-L) load fed from an AC power source of sinusoidal voltage and current waveforms, describing its three components, their waveforms, their power triangle, and units.
Please and thank you
A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown capacitor. The voltage drop across the resistor is 102 V. Find the, a.) current of the circuit b.) impedance of the circuit c.) Capacitive reactance d.) capacitance value.
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
1. For the circuit in Figure 1: a) What is the RMS-value, zero-phase angle and frequency of voltage source e(t)? b) What is the total impedance of the circuit? c) Calculate frequency domain voltage Uc and current It (present solution in po- lar form x < yᵒ). d) Calculate time domain voltage uc(t) and current ito(t) (present solution as sine- wave function of time) e(t) = 170 sin (100nt +25°) V, R/= 102, C = 15 μF Answers: Ztor 212.422-87.3°, tot 0.57 AZ112.3°, ito(t)=0.8 sin(100xt+112.3⁰) This homework is to be presented during exercise 14 on 24.4-28.4. Bonus question: Calculate value of voltage e(t) and current isot(t) when /= 1s. Extra points can be earned by solving this question, however it is not mandatory. e(t) ↑ Utot Figure 1. R UR C HH Uc
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram. please answer it based on your knowledge. thank you so much!)
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram and question. please answer it based on your knowledge. thank you so much!)
Pls answer d. Only
Consider the two industrial loads that are connected to the source as shown in Figure. We would like design a compensation system to correct the power factor as seen from the source. The Source and the feed line between the source and 40kW source is not accessible, but the feed line between the loads is in the factory, although it is fixed (you cannot change it). The voltage across the 18kW load must be kept constant at 220V(rms).(a) Calculate the value of Vs, without compensation.(b) How must we connect the compensation capacitor(s) to the system? Possible choices are:Between the terminals ofi. the source,ii. the 40kW load,iii. the 18kW load,iv. both loads,v. the source and both loadsJustify your answer.(c) We want to set the power factor of the source to 0.96 (lagging). Calculate the impedanceof the capacitor(s) required, according to choice you made in part (b). The frequency ofthe operation is 50HZ