10. The 8-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 12 mm and an outer diameter of 20 mm. If the original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively, determine the strains in the sleeve and the bolt if the nut on the bolt is tightened so that the tension in the bolt is 8 kN. Assume the material at A is rigid. Eat = 70 GPa, Emg = 45 GPa. 50 mm - 30 mm [Ans: €b = 0.00227; ɛs = 0.000884]

10. The 8-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 12 mm and an outer diameter of 20 mm. If the original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively, determine the strains in the sleeve and the bolt if the nut on the bolt is tightened so that the tension in the bolt is 8 kN. Assume the material at A is rigid. Eat = 70 GPa, Emg = 45 GPa. 50 mm - 30 mm [Ans: €b = 0.00227; ɛs = 0.000884]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 5 High-strength stainless steel is required for use in building structures and equipment (e.g. , cranes). It is produced by heat treating quench-hardened steel in a process called tempering that reduces brittleness and imparts toughness. In a production facility, alloy steel plates (k=50 W/(m K), c=460 J/(kg K) and p=7865 kg/m³) of thickness 3 cm have to be tempered in a convective oven by heating them to 550°C. If the plates are initially at 40°C and the air inside the heat treating oven is at 700°C with a convective heat transfer coefficient of 45 W/(m? K), determine how long the plate has to remain in the oven.
A force P of 70 N is applied by a rider to thefront hand brake of a bicycle (P is the resultant of anevenly distributed pressure). As the hand brake pivots atA, a tension T develops in the 460-mm long brake cable(Ae = 1.075 mm2 ), which elongates by δ = 0.214 mm.Find the normal stress d and strain in the brake cable.
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.55 in., -0.17 in.). Assume a = 10 ft, b = 20 ft, c = 7 ft, and d = 14 ft. Determine the normal strain in each bar. Answer: EAB || A EBC= i P a (1) y B με με b (2) C d
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
8-21. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. When the applied load on the specimen is 50 kN, the diameter is 12.67494 mm. Determine Poisson's ratio for the material. 8-22. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P = 60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. σ (MPa) 490 0.007 Probs. 8-21/22 € (mm/mm)
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a = 290mm, b = 120mm, c = 80mm, and e = 35°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 36 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F2 Support bracket A a Answers: Tpin B = MPa Ob = i MPa