10. For the circuit of Fig. 5.80: a. Find the total resistance, current, and unknown volt- age drops. b. Verify Kirchhoff's voltage law around the closed loop. e. Find the power dissipated by each resistor, and note whether the power delivered is equal to the power dis- sipated. d. If the resistors are available with wattage ratings of 1/2, 1, and 2 W, what minimum wattage rating can be 22 1 10n 5.6 33 1 used for each resistor in this circuit? FIG. 5.81

10. For the circuit of Fig. 5.80: a. Find the total resistance, current, and unknown volt- age drops. b. Verify Kirchhoff's voltage law around the closed loop. e. Find the power dissipated by each resistor, and note whether the power delivered is equal to the power dis- sipated. d. If the resistors are available with wattage ratings of 1/2, 1, and 2 W, what minimum wattage rating can be 22 1 10n 5.6 33 1 used for each resistor in this circuit? FIG. 5.81

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

how-much-voltage-will-be-dropped-across-a-40kw-resistance-whose-current-is-250 micro amperer
I need a detailed answer on this please. 1.Depending on voltmeter/ammeter terminal connection to the components, you might find differentsigned voltage and currents values for the same component. This causes different signed powervalues for the same components therefore we cannot state whether components generate orabsorb power. What is your solution to this chaos?
Choose the correct answer
2. For the network of figure below: a. Find the total conductance and resistance. b. Determine Is and the current through each parallel branch. c. Verify that the source current equals the sum of the parallel branch currents. d. Find the power dissipated by each resistor, and note whether the power delivered is equal to the power dissipated. e. If the resistors are available with wattage ratings of 1/2, 1, 2, and 50 W, what is the minimum wattage rating for each resistor. 0.9 V Gr Rr R₁30 R₂60 R₂ 1.5 Ω
3. In Figure, the battery voltage is V=10 volts, and the values of the resistances, in ohms, are 100, 220,and Kas shown. Find: (a) Total resistance seen by the battery, (b) Current measured by the ammeters shown in the figure, (c) Power output of the battery, (d) Power input to each resistor. V 10082 220 Ω 1ΚΩ
A galvanometer has resistance 5 ohm and full scale deflection 20 milliampere. Calculate the value of the maximum current when a shunt of 0.1 ohm is connected to its coil. Also, calculate the value of the potential multiplier which is to be connected to the galvanometer to make it a voltmeter that reads up to 5 volt.
A resistor R is connected in parallel with a 10-ohm inductive reactance. The combination is then connected in series with a 4-ohm capacitive reactance. The whole combination is connected across a 100-volt, 60 Hz supply, How much is R if the angle between the supply voltage and the total current is 45 degrees? ANSWER: 20 ohms
Q: A wood panel containing 16 solar cells. Calculate the total open circuit voltage and short circuit current coming out of the board and draw the relationship between current and voltages in the following cases 1- If you connect each two cells in series and connect the groups in parallel. 2- If all four cells are connected in parallel and the groups are linked in succession, noting that each cell has the following characteristics: Vos = 0.75V, Isc = 2 mA
For the circuit shown in the figure, determine the current and voltage in all Write your answer in a data table:
4H Q.13: For the circuit shown, calculate the current in each branch and the consumed power in each branch resistance. Use v=100cos344t Vol. (Ans.: P3=34.6W, Ps=26W & P20=86.5W) M=4.5H 82 62 Vs १9H 202
A scientist working under emergency conditions at a jungle based lab realizes that her primitive radio has shorted in the rain and burned out a resister. She wants to match the original resister of 2.50 Ohms but believes that a resistance between 2.25 - 2.75 Ohms would be sufficient. All she has to work with is a spool of fine lead soldering wire and some scrap equipment. a) The wire has a diameter of 1.5 mm and the resistivity of lead is 22*10-8Ohm-meters. How much lead wire would she need to make the resister? b). Looking around the lab she is able to scavenge two 3.5 ohm and one 1.0 ohm resisters from old equipment. Using these three resisters how close can she come to building a 2.50 ohm resister? Explain the optimal configuration and calculate the equivalent resistance.