10. For a 10 Mbps data link using 12,000-bit frames, and assuming that electrical signals propagate at 2.5 x 108 m/s: a. How long does it take to introduce a single frame onto the link? b. How long does it take for the trailing edge of the frame to travel 1,620 km? c. What is the total transmission time of this frame, from start to finish?

10. For a 10 Mbps data link using 12,000-bit frames, and assuming that electrical signals propagate at 2.5 x 108 m/s: a. How long does it take to introduce a single frame onto the link? b. How long does it take for the trailing edge of the frame to travel 1,620 km? c. What is the total transmission time of this frame, from start to finish?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

a. If sixteen users are connected to a wireless network that offers a maximum data rate of 500 Mbit/s and a throughput of 40%, what is the typical average practical message data rate available for each user? (Express your answer in Kbit/s) b. A communication system using a special version of phase modulation which is 8 PSK have a symbol rate of 50000 symbols/s. Calculate the bit rate for this communication system?
Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data frames carry a useful payload of size 12,000 bits. Assume that both ACK and data frames have 320 bits of header information, and that ACK frames carry no data. What is the effective data throughput When using Stop and Wait?
Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of cable are needed for a full duplex transmission link to have a minimum capacity of 1500 bytes?
Suppose there is a b+n (Sum of first and last digit of your Reg#) Mbps microwave link between a geostationary satellite and its base station on Earth. Every minute the satellite takes a digital photo and sends it to the base station. Assume a propagation speed of 2.4*108 meters/sec. 1. What is the propagation delay of the link? 2. What is the bandwidth-delay product?
Imagine the length of a cable is 2500 metres. If the speed of propagation in a thick co-axial cable is 60% of the speed of light, how long does it take for a bit to travel from the beginning to the end of the cable? Ignore any propagation delay in the equipment. (Speed of light c = 3 x 108 metres / sec)
7. Two channels, one with a bit rate of 190 kbps and another with a bit rate of 180 kbps, are to be multiplexed using pulse stuffing TDM with no synchronization bits. Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
4. Three input channels need to be multiplexed using TDM, Their bit rates are 120 kbps, 80 kbps, and 40 kbps, respectively, (a) What is the required output bit rate for the TDM? (b) How to set the relative size of each time slot in one frame? (e) What is the minimum frame size and the corresponding frame rate?
What is the delay of sending a data file from a source station to a destination station? Suppose that the length of the data file is 2 Mbytes and the bandwidth of the channel is 1600 bps, and the network link between the sender and receiver is 20000 Km and the speed of the light inside the link is 2x108 meters/second? Assume that the delay is composed of only transmission time and propagation time.
QUESTION 28 An engineer has designed transmission equipment to transmit 7200 symbols per second while encoding 8 bits per symbol. If the signal to noise ratio is 400:1 and the channel bandwidth is 3625 Hz, has the engineer's design exceeded theoretical limits? O Yes, both the limit on symbol rate and the limit on bits per symbol have been exceeded. O Yes, but only the limit on symbol rate has been exceeded. O Yes, but only the limit on bits per symbol has been exceeded. O No, none of the theoretical limits have been exceeded.
Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the intended capacity is 8 Mbps. a. What should be the signal-to-noise ratio (SNR) to obtain this capacity? Constant values= c=3x^10°m/s, k=1,38x^10231/K I
Four channels, two with a bit rate of 120kbps and two with a bit rate of 880kbps, are to be multiplexed using multiple-slot TDM with no synchronization bits.Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
Consider a communication channel with bandwidth B = 8000 Hz. Suppose the channel has a signal-to-noise ratio S/N = 541. What is the maximum data rate of this channel? ? What is the minimum number of signal levels needed to achieve a data rate of 64000 bps?