10. Determine Ma when As'= 2,027 mm², As = 4,054 mm? Note: fek = 24 MPa, fy = 400 MPa, ē = 0.85B, Iek 4. f, d ɛ,-8, As 8-D25 300 mm uu 59 610 mm 635 mm 700 mm

Q: FIND PA - PB

A:

Q: 150 12 mm N.A 466.09 mm

A:

Q: a. Determine the critical slenderness ratio of the built-up column section.  b. Determine the…

A: Welding: - It is a process in which two metals joins by using high temperature heat that melt parts…

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: P= 250 KN W= -7x+81 KN/m Note According to the company guidelines i am able to answer only first…

Q: Figure 50 mm 150 mm 150 mm 300 mm 1 of 1 Locate the centroid y of the bea Express your answer to…

A:

Q: 4. The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their…

A: Data Given: GAB = 44 GPaGBC = 26 GPaLAB = 150 mmLBC = 120 mmrAB = 28 mmrBC = 45 mmt = 4.2 mmτAB =…

Q: 40mm L-600mm P = 20kN 20mim

A:

Q: Replace the loading on the frame by a single resultant force. Suppose that F₁ = 450 N.F₂ = 650 N. F…

A:

Q: ) Determine Ma using method I in which the T-section is divided into two parts, i.e., overhanging…

A:

Q: 125 mm 345 mm Answers: x = y = Z: i i i 145 mm 225 mm 170 mm mm mm mm

A:

Q: A=7 B=7 D=2 C=5 E=8 F=4 Change letters into numbers... Determine the total area (mm2 ) of the given…

A: Given data: A=7B=7D=2C=5E=8F=4 It is asked to: 1. Determine the total area (mm2) of the given…

Q: Plane a-a is called the D.

A:

Q: Paint issues from the tank at Q=0.00354 m³/s. Find the kinematic viscosity. A 3m 1.650x10-4 m²/s…

A:

Q: Determine the horizontal deflection of D. Fy-20.00 B Fx-10.08 3.0 m 4.0 m D 3.0 m Consider the…

A:

Q: 2 Knowing that a beam of the cross section shown is bent about a horizontal axis and that the…

A:

Q: 2) What is the deformation 8gc in mm?

A:

Q: Determine the steel area required for the section shown: If Mu = 1500 KN. M 70

A:

Q: Solve for the centroid of the figure relative to the bottom fiber. You'll be solving only for the y…

A: Unsystematic section is given and it has been asked to determine centroid of y axis. Please refer…

Q: Determine Mn iff'y = 60,000psi and fe=4,000psi. use (IS 456) -24 in. 4 in.

A: The values given in the question are as followsYield strength of steel(fy)=60,000 psi or 413.685…

Q: the centroid of the area shown. In part (b), note the sym- nifying that the area is symmetric about…

A:

Q: 10 mm 70 mm 50 mm yo

A:

Q: Compute the design strength.

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 1. Suppose that P=104lbs. What will the force Q be in this case? 2. Suppose that P=91lbs. What will…

A:

Q: Three forces are acting on the eyebolt shown below. All forces intersect at a common point O.…

A: Given data in question  Forces 2500, 3000 & 4000 Angles 45, 25 & 30° To find out  Resultant…

Q: Problem: Determine the midspan deflection, and if the deflection max is limited to 6 mm, find Ely =…

A: Introduction- The tangent traced to the elasticity curve at the moment of maximum deflection in…

Q: Find ØMn for the beams of cross section shown. Assume physical dimension are acceptable. 760 fc' -…

A: As per mentioned in question,  effective cover of tension reinforcement  and bottom width are…

Q: Locate the centroid y of the beam's cross-sectional area. Take a = 45 mm (Figure 1) Express your…

A: Find centroid :y=A1y1+2A2y2A1+2A2

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

A:

Q: I also attached a formula sheet we can use and we are also given the information about the w shapes…

A:

Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…

A:

Q: The centroid of the T-section shown is 2.5 inches above the base. What should be the value of b to…

A: Given A T section having centroid 2.5 inch above the base.  Required Value of b

Q: Given:  fy = 345 Mpa f'c = 28 Mpa Determine the depth of compression block in mm in 3 decimal…

A: Given:- fy=345 MPafC'=28 MPaWidth of section,b=250 mmDepth of section,d=600 mm3 bars of 28 mm…

Q: 0/10 FIND DEFLECTION IN Aluminum. IF E st= .200000 MPa, Ealu.=7000O MPa 100 kN R ALU.=30 MM Aluminum…

A:

Q: Show complete solution e Determine the following unknowns using Double Integration Method. consider…

A:

Q: The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also…

A: A rigid bar ABCD as shown-P=78 kNTo Find-The value of diameter at pin B.

Q: 0.5 EI mm S=10 40 EI -5 2 E = 2.1+ 10 N/m² I=70,000 cm4 √ = 10 mm a EJ 2EI b At = 10°c h t = 20%…

A: The given structure is a beam with a span of 2 meters, supported at both ends. The beam has a…

Q: Dimensions in mm 80 Y 10 -60 DETERMINE THE VALUE DISTANCE OF "X". DETERMINE THE VALUE DISTANCE OF…

A:

Q: Ex's For the beam shown below, Find (Wii), use fo`=21/pa. EYE 400 Mpa.... Wu 5m. 100m 100m 100mm…

A: Given: b = 200 mm d = 350 mm span = 5 m fc = 21 MPa fy = 400 MPa

Q: 400 mm

A:

Q: Given the following: b=360mm d=550mm fc'=35MPA fy=420MPA Mu=700KN-m Determine As LISE N SCR 2015 As…

A:

Q: substitute: C=9, E=22, H=12 A built-up section is shown in figure (a) Determine the thickness "t" of…

A: ASKED: To determine- thickness of the horizontal plate 't', for given condition moment of inertia…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.