10. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.17 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 85.6°C. For each copper bar, A= 500 mm2 , E = 120 GPa, and a = 16.8 um/(m-°C). For the aluminum bar, A = 400 mm2 , E = 70 GPa, and a = 23.1 µm/(m•°C). Copper Aluminum Copper 750 mm

10. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.17 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 85.6°C. For each copper bar, A= 500 mm2 , E = 120 GPa, and a = 16.8 um/(m-°C). For the aluminum bar, A = 400 mm2 , E = 70 GPa, and a = 23.1 µm/(m•°C). Copper Aluminum Copper 750 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 mm while those at CD decrease 70 x 10 3 mm in the 280-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 50 mm, b = 130 mm, and c = 80 mm. gage length a mm B b mm Co C mm
S=25
Situation 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. Steel A = 550 mm² 10. Compute the axial stress at the bronze 11. Compute the axial stress at the aluminum 12. Compute the axial stress at the steel 60 KN 3.0 m Aluminum A = 400 mm² 2.0 m Bronze A = 220 mm² 20 KN 1.0 m 30 kN
solve simultaneously using 2 equations to find Tc, Nab, Fab. Whole decimal pls
Knowing that a 0.03-in. gap exists when the temperature is 85 °F, determine the temperature at which the normal stress in the aluminum bar will be equal to-11 ksi. T= OF 0.03 in. 12 in. Bronze A = 2.2 in.² E = 15 × 106 psi a = 12 x 10-6°F 16 in.. Aluminum A = 2.8 in.² E = 10.6 × 106 psi a = 12.9 × 10 6 °F Ans = 250
d) Calculate the change in temperature. Indicate increase or decrease in temperature.
4. A uniform bar with an area of o.25 in- is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume a = 6.5 × 106 in/(in-°F) and E = 29 × 10ʻ psi. %3D %3D
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown -3 are found to increase 50 x 10°mm while those at CD decrease 70 x 10 mm in the 270-mm-gage length. Using E - 190 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a= 50 mm, b= 140 mm, and c = 70 mm. !3! gage length a mm b mm C mm
I need the answer as soon as possible
The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm
Problem #2 (5 points): Fig. 2 shows aluminum hollow rods (outer diameter is 2 in. and inner diameter is 1.5 in.) that are fixed to rigid walls. The gap between the rods is 0.005 in when the temperature is 60°E. If the temperature is 200°F, what is the stress in each rod? aai = 13 x 10/F, Eai = 12 x 10 ksi %3D 0.005 in. .8 in. Fig. 2 Page | 1
Problems: Stress (ksi) 53.2 1. Determine the ductility (u) of the material based on the stress- strain diagram (problem S5.1). 43.6 37.1 0.0013 0.0063 0.163 0.247 Strain (in/in)