10. A typical ceiling of a house consists of the items in the accompanying table. Assume aninside room temperature of 70°F and an attic air temperature of 15°F, with an exposed areaof 1000 ft?. Determine the temperature distribution through the ceiling. Also calculate heatloss through the ceiling.ab bood ta bon odi of(s) 1.2.3.4.Problem 11.13ResistanceItems(h • f² • °F/Btu)1. Inside attic film resistance2. Insulation batt (6 in.)0.6819.03. Gypsum wallboard (1/2 in.)4. Inside film resistance (winter)0.450.68

Answered: Image /qna-images/answer/4f0e9b6c-3983-4af4-aa62-b38061fe7d61.jpg

Answered: 10. A typical ceiling of a house…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) A wall section composed from the outside to inside, of concrete brick 100mm thick, an air space of 50mm, two layers of fiberglass insulation 38mm thick, concrete block 150mm thick and air space of 19mm and a gypsum board of 13mm. The exterior conditions are -20C and RH=90% while the interior conditions are 23C and RH=40%. The surface temperature from the outside to inside are shown in the figure. The permeances are: Still Air: µ = 175 ng/pa.s.m Fiber glass: M=2560 ng/pa.s.m? Concrete block: M= 200 ng/pa.s.m? Gypsum board: M= 2000 ng/pa.s.m? Concrete brick: µ = 4.55 ng/pa.s.m Determine if there is a risk of condensation, and if there is, what is the condensation rate? What would happen if a vapor barrier (M=0.2 ng/pa.s.m²) was installed on the warm side of the insulation (Surface 4). 21с 19C 16 С 12C -10 -15C -18C -19C Gyp Air Concrete Fiber Fiber Air Concrete Outdoor Indoor sum block Glass Glass brick 230 19 50 mm -20C 13 150 mm 38 mm | 38 mm 100 mm RH=90% RH=40% mm mm Surf. 1 Surf.…
The diagram below illustrates a simplified version of the Jet Propulsion Laboratory's 25-ft space simulator chamber. Within it, tests are run for deep space probes and their components. In this particular experiment, a sensor assembly with its housing is placed inside. The sensor-housing electronics create heat such that q=3181.0 W exits the assembly's top surface into the chamber. The chamber itself is under vacuum, and its walls are at cryogenic temperatures to simulate conditions in space. Surfaces 1 and 2 are flat. Assume they are flush. The top surface of the chamber, Surface 4, can be approximated as a perfectly insulated, flat ceiling. The exposed surface of the floor, Surface 2, is a black, donut- shaped surface. Additional surface information can be seen below, including various parameters and dimensions. Assume all surfaces are opaque and diffuse, and conditions are at steady-state. PARAMETERS & DIMENSIONS Surface 1: A = 7.07 m²; diameter d; = 3 m; &₁ = 0.5; Surface 2: A₂ =…
Ans. 0.9 m Q2/A vertical cylinder having a length of 30 cm is maintained at 100-C and exposed to room air at 15-C. Calculate the minimum diameter the cylinder can have in order to behave as a vertical flat plate. Ans. 9.01 cm

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS