10 V + w 240 Ω w w 180 Ω 300 Ω 140 ΩΣ 200 Ω w

Q: The power absorbed by a circuit is p(t)=2.5e-4t W. How much energy will be delivered by the circuit…

A: If p(t) is the instantaneous power associated with a circuit, then the energy delivered by the…

Q: 100 Vz 7.5 Vz 15 Pmax=1W 1N2805 250

A: Given

Q: Construct the Karnaugh map for the logicfunction defined by the truth table,and find the minimum…

A:

Q: The power dissipated by a 10-ohm load resistor with a current rating of 5 amperes is if supplied…

A: Given, Resistance, R=10 Ω Current rating, Irated=5 A Supply, Vs=20 V

Q: For the waveform of Figure, determinea) Period  I got 100us b) Frequency  I got 10kHz c)…

A: a) Given time = 525usNumber of cycles for 525us =  5 cycle + 1/4 cycle = 5.25 cycle.So period =…

Q: If a potential difference of 2.15 volts is applied to an unknown resistance and the measured current…

A: Given: Potential difference =2.15 V is applied across unknown resistance and current is also unknown…

Q: №g + SIO 5 Va - Then calc. power, P=VI

A: Here we have to find the voltage Vg and power P.

Q: Figure 2a. Total Current Figure 2b. Bulb Current A 220V 100W 220V 100W A L L 2.5372H 2.5372H 220V…

A:

Q: What is the range of the output voltage of the circuit if the input can vary from 0.1 to 0.5 V?

A: GIVEN THAT

Q: 10. What unit is Inductance is measured in? Faraday Lenz Choke Henry

A: Resistance is measured in ohms Capacitance is measured in farads

Q: 19. What are the ms and peak currents for a 60 W bulb? (The ms voltage is the usual 120 V.) A. 0.71…

A:

Q: Convert 100 micro ohm to Fahrenheit degrees.

A: Since Ohm Ω is the unit of resistance and Fahrenheit is the unit of Temperature. And resistance can…

Q: what is the main parts of Energy meter

A: There are four essential parts of an energy meter.

Q: in the case of 50Hz systems, how many discharges will occur in 10ms if you have 20 discharges in 1…

A: The solution is given below.  The frequency is 50 Hz. The time period will be 20 ms.

Q: Estimate thermal voltage for 30o C.

A: The thermal voltage (VT) is a very important quantity in semiconductor physics. It is dependent on…

Q: What will be the voltage drop across a 5 mH indjctor if 2.5sin(20t) A current flows through it?

A:

Q: The reading of the AC voltmeter is 40 V rms. Find the following: Figure 1 a. The value of the peak…

A: According to the question, for the given circuit as shown belowThe reading of the AC voltmeter is 40…

Q: R1 1 ww- High voltage de supply C Us R2 10W 8 3W

A:

Q: Refer to the Figure 2 below, what the the given voltage levels represented by letters A, and B?

A: It is given that:

Q: e peak voltage

A: RMS voltage- Root mean square value is a amount of AC power drawn by resistor equivalent to DC power…

Q: In Figure 2, what is Vo in rms volts? 16 kW 0.9 pf lagging 20 kW 6/0° A rms Vo 0.8 pf lagging Figure…

A:

Q: A 5.3 V zener is rated at 1.5 watt. The maximum zener current is equal to a. 2.83 mA. O b. 283 mA. O…

A: In this question we need to find a maximum zener current .

Q: One disadvantage of low power factor is

A: The solution is provided in the following section:

Q: From the figure below calculate the total charge due to the charge distributions labeled A (line…

A: Continuous charge distribution refers to the dispersion of charges along a line, surface, or volume…

Q: For the waveform of Figure, determinea) Period  I got 95.45usb) Frequency  I got 10.476kHzc)…

A: a) Time for 5 cycle + 1/4 cycle is 525us5 cycle + 1/4 cycle = 5.25 cycleSo period = 525/5.25 = 100us…

Q: The relation between electric intensity E, voltage applied V and the distance d between the plates…

A: Given: E = Electric Field ; V = Voltage applied ; d = Distance between Plates

Q: T To what voltage the machine will excite when the ficld resistance is 55 0 and the spced 800 rp.m.…

A: In this question,  Saturation curve of the shunt generator is given.  Find the filed resistance for…

Q: What will be the value of thermal voltage of Si at 300 K?

A: Write the expression for thermal voltage,

Q: For the subtractor, if V2 equals 5 volts DC, and V1 is 4 volts DC, then the O/P is A The answer is 4…

A: In this question,  We need to choose the correct option What is output voltage?  If V1= 5V V2= 4V

Q: What does s/c and 115 ohms mean?

A: Given: