10 m 8 m 1.2 m B 200kg |2 m 12 m

Q: Two flowerpots are supported with cables as shown in the figure. If pot A weighs 16 lb and mot B…

A: Given data  Weight of A = 16 lb Weight of B = 9 lb Find the tension in each cable and angle alpha.

Q: Points B, D, and C lie on the x-y plane and vertical force F is on the z-axis. If force F subjected…

A: Given: The coordinates of different points are : O= (0,0,0)A=(0,0,-4)B= (3,3,0)C = (2,4.5,0)D =…

Q: he uniform plank ABC weighs 40 kg. It is supported by a pin at A and a cable that runs around the…

A:

Q: Determine the tension at AC. 2 m. 2 m. B cable -60 w =30 kN bar B.

A: Given dataWeight of the block W =30kNTo determine the tension in the cable AC

Q: A 363.8N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC…

A: Consider the free body diagram shown below for the given system.

Q: Determine the tension developed in cables AB, AC, and AD 2 m 1 m 30 2 m B 600 N

A:

Q: Problem 2 A transmission tower is held by three guy wires anchored by bolts a с, and D. If the…

A:

Q: 4. In the figure shown, A. Draw the FBD and show all the forces acting on beam AB. B. Determine the…

A:

Q: The ramp shown weighs 400lb and is hinged to the truck frame on each side. it is also held in the…

A:

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

A: Free body diagram:

Q: Three cables are used to tie the balloon shown in Figure. Determine the magnitude of the vertical…

A:

Q: A horizontal beam weighing 300 N is attached to a wall. It is supported by a cable which makes an…

A:

Q: A uniform brass plate with area of 18 m?, has weight of 51 kg which is hold by three cables in the…

A:

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A: we solve this question by resolution of component of force in 3D ( 3 dimensions). given dimensions…

Q: A container of mass m = 120 kg is supported by three cables as shown. Draw the free-body diagram…

A: To determine the tension in each cable, take all forces on point A and draw free body diagram

Q: The system shown is supported by cables BC and BD, as well as a ball-and-socket joint at point A.…

A:

Q: Determine the horizontal and vertical components of force that the pins C and D exert on member ECD…

A: Determine the horizontal and vertical components of force that the pins C and D exert on member ECD…

Q: For the shown frame structure, the uniform beam AB weighs 480 lb and the uniform column CF weighs…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A: Given: The tension in cable AB, TAB = 9.6 kN The length, a = 47 m The length, b = 54 m The length, c…

Q: Water pressure in the supply system exerts a downward force of 30 lb on the vertical plug at A.…

A: The downward force at vertical plug A is .

Q: A homogeneous rod AB weighs 100 N. The end is attached to the wall with hinges, while the B end is…

A: Given Beam weight = 100 NDead weight = 200N To find Free body diagram Tension in rope BC

Q: Q3) If the mass of cylinder A is 40 kg. determine the mass of cylinder C in order to hold the…

A:

Q: 2. Two cables support a 400- Ib weight as shown. Determine the tension in each cable. 400 - Ib

A:

Q: CHAPTER FOUR Equilibrium of Coplanar Forc 4.13 Calculate the horizontal force F that should be…

A: Given data  Weight = 100lb Angle = 30° with the vertical. Find the force F

Q: en the end of the strut and the wall. Assuming that the entire weight of the sign is he strut, find…

A: Given: The weight of strut is, W1=425 N. The weight of the sign board is, W2=235 N. The angle…

Q: 3.13 The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying…

A:

Q: bearings C and D) as shown below. Determine the tension in cable AB and the support reactions at…

A:

Q: Show the complete solution: Two cables tied together as shown in figure , Knowing that Q = 60 lbs…

A: Consider the free body diagram of the point C.

Q: A sign that weighs 15.0 N hangs from the end of a beam of length 4 meters and weight 10 Newtons.…

A: To obtain the tension in the rope, we must balance the moment produced by the tension (T) and the…

Q: A uniform beam ( weight 71 N, length 6m) is being supported by cable and a hinge on a wall. The…

A:

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A:

Q: Member AB is supported by a ball-and-socket joint at end B, and by a smoo vertical wall at end A,…

A:

Q: 4. Assuming you know the geometry of the ropes, you cannot determine the forces in the cables in…

A: Condition of static equilibrium: There are three conditions of static equilibrium for any static…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.