10 in 1 in 1 in V 12 in 1 in 5 in The steel wide flange beam shown above is fabricated using three rectangular plates, welded together. Assume the following cross-section properties: A = 27 in3 • Y 8.204 in (distance from bottom of shape to neutral axis) • | = 739.88 in (moment of inertia about neutral axis) The beam is subjected to a shear force V = 20 kips. Which of the following is closest to the shear flow carrled by the weld attaching the top flange (10" x 1" top piece) to the rest of the cross-section?

10 in 1 in 1 in V 12 in 1 in 5 in The steel wide flange beam shown above is fabricated using three rectangular plates, welded together. Assume the following cross-section properties: A = 27 in3 • Y 8.204 in (distance from bottom of shape to neutral axis) • | = 739.88 in (moment of inertia about neutral axis) The beam is subjected to a shear force V = 20 kips. Which of the following is closest to the shear flow carrled by the weld attaching the top flange (10" x 1" top piece) to the rest of the cross-section?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained under a sustained ultimate bending moment of 1,200 kN.m. Compression bars centroid is 70 mm from beam edge. 4,387 3,839 6,180 5.353
Question 1) F=35 kN single load, M=45 kN.m moment and w=16 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is also given as L=4 m. The cross-sectional properties of the beam are; body height yg=225 mm, body thickness xg=14 mm, flange width xf=194 mm, flange height yf=11 mm. Point P on the section is located just above the flange-body junction. It is desired to determine the stress state at the P point in the section taken from the B line of the beam. According to this;Question1-A) Find the shear force (VB) at point B. (Write your result in kN.)Question1-B) Find the bending moment (MB) at point B. (Write your result in kN.m.)Question 1-C) Find the moment of inertia of the beam section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005.)
Parvinbhai
need corrrect and urgent
Find the maximum transverse shear stress value. Find the maximum bending stress σb Find the maximum normal stress and the maximum shear stress developed in the shaft
Find the shear force and bending moment 1.5 m, 3 m, and 4.5 m from the left end of the beam. 9 kN/m 3 m Answer: x = 1.5 m: V = 3 m: V = 0, M = 27 kN • m x = 4.5 m: V = -10.125 kN, M : 10.125 kN, M = 18.625 kN·m %3D %3D 18.5625 kN · m %3D
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 16 mm d = 120 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1737 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 254790000 mm4. If the beam will be subjected to a shear force of V = 250 kN, determine the shear stress at point K, located at yK = 80 mm below the z centroidal axis.
A simply supported wood beam with a span of L = 11 ft supports a uniformly distributed load of w = 840 lb/ft. The allowable bending stress of the wood is 1400 psi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 1.5, determine the minimum width b that can be used for the beam. O 5.54 in. O 7.03 in. O 6.62 in. O 8.58 in. O 4.15 in. L h