10) a turbine operating under steady flow conditions receives 4500 lg of steam per hour. The steam enters the turbine at a velocity of 2800m/min, an elevation of 5.5 m and a specific enthalpy of 2800 kj/kg. It leaves the turbine at a velocity of 5600 m/min, an elevation of 1.5 m and a specific enthalpy of 2300 KJ/kg. heat losses from the turbine to the surroundings amount to 16000 KJ/hr. Determine the output power of the turbine.

10) a turbine operating under steady flow conditions receives 4500 lg of steam per hour. The steam enters the turbine at a velocity of 2800m/min, an elevation of 5.5 m and a specific enthalpy of 2800 kj/kg. It leaves the turbine at a velocity of 5600 m/min, an elevation of 1.5 m and a specific enthalpy of 2300 KJ/kg. heat losses from the turbine to the surroundings amount to 16000 KJ/hr. Determine the output power of the turbine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: why is NB=0

Q: ir at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass…

A: The inlet pressure at turbine is .The inlet temperature is .The efficiency of turbine is .The exit…

Q: A juice at a rate of 500 kg/h is heated from 60 °C to 115 °C. The juice has a specific heat of 3.85…

A: Introduction In this problem, we will calculate the mass flow rate of steam with the help of the…

Q: Consider a regenerative gas-turbine power plant with two stages of compression and two stages of…

Q: Chesterfield currently uses 11,400 m³/d (average flow) of water which is drawn from a storage…

A: Given data: Average flow per day = 11400 m3 Minimum flow during winter = 0.25 x Average flow Peak…

Q: A well-insulated turbine at steady state develops 10,000 Hp when provided with a steam mass flow…

Q: The power output is 12122 kW

Q: Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa,…

Q: The figure below shows a mixing tank initially containing minitial = 3000 lb of liquid water. The…

A: Given:Initial mass of water in the tank, mi=3000 lbMass flow rate of hot water, m1=0.8 lb/sMass flow…

Q: In a gas turbine plant operating on the constant-pressure cycle, the pressure ratio is 5 and the…

A: As per given question We have to determine theoretically output on kw

Q: A flashed-steam geothermal power plant is located where underground hot water is available as…

Q: 1) Pasteurized beer (Cp = 4.2 kJ/kg °C) is being cooled in a double pipe heat exchanger. The beer…

Q: Steam enters a well-insulated turbine at 500 bar and 600oC with a velocity of 100 m/s. The stream…

Q: erativ bine engine at 310 K and 100 kPa, where mpressed to 900 kPa and 650 K. The reg ectiveness of…

A: given: Temperature of air at the entry of the compressor = 310 k Pressure at the entry of the…

Question

10) a turbine operating under steady
flow conditions receives 4500 lg of
steam per hour. The steam enters the
turbine at a velocity of 2800m/min, an
elevation of 5.5 m and a specific
enthalpy of 2800 kj/kg. It leaves the
turbine at a velocity of 5600 m/min, an
elevation of 1.5 m and a specific
enthalpy of 2300 KJ/kg. heat losses
from the turbine to the surroundings
amount to 16000 KJ/hr. Determine the
output power of the turbine.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. A 1.5 kW pump delivers 1.2 kg/s water to a building. The water comes in at 100 kPa, and 15°C. The outlet water velocity must be 30 m/s and the pump has an isentropic efficiency of 75%. What is the maximum exit pressure the pump can produce? (Answer: 587.5 kPa) *Hint: The Mechanical Energy Balance may be making a return on this problem!
Refrigerant 134a enters an air-cooled condenser at 12 bars and 60°C, and leaves as a saturated liquid at 12 bars. Atmospheric air at 35°C is blown over the condenser tubes and leaves at 45°C. The heat transfer between the two flfluid streams equals 25 MJ/h. Changes in kinetic and potential energy are negligible. Make any reasonable assumptions if necessary. Determine (a) the mass flow rates for the R-134a and the air, in kg/h, Hint: Use the energy conservation on each of the ⁅ uid streams separately. (b) the entropy production rate in the condenser, in kJ h-1K-1, Hint: Use the entropy balance over the whole condenser. (c) the change in kinetic energy for R-134a if the pipe diameter is 2.0 cm, in kJ/h (d) Draw the T-s diagram for the process for R-134a.
In a gas turbine plant operating on the constant-pressure cycle, the pressure ratio is 6 and the maximum and minimum air temperatures are 1,088 K and 272 K respectively. Determine the theoritical output (Wnet) in kW, of the plant if mass flow rate is 1 kg/s. Take y = 1.4 and Cp = 1.005 kJ/kgK
Determine the efficiency of the reversible Heat Engine cycle shown: TA 4 5 800K 2 3 600K 6 300K 1 S (kJ/kg-K) 0.1 0.3 0.4
A Stirling cycle operates with air with a volume flow rate of 0.5 m³/s at the beginning of isothermal compression. After compression, the volume flow rate is reduced by 75% of its initial volume. Assuming that the maximum pressure in the cycle is 1.2 MPa and if the heat rejected is 50 kW at 300 K, determine the mass flow rate of air and the ideal thermal efficiency of the cycle. Match each item to a choice: MASS FLOW RATE IDEAL THERMAL EFFICIENCY Choices: 79.65% 24.04% 0.3093 kg/s 23.05% 76.95% 0.5122 kg/s 0.4189 kg/s NONE OF THESE
In a steady-state operating power plant, saturated liquid H2O at 122 deg C is fed to a boiler at 3.756 m/s through a pipe (0.03 m diameter). It leaves the boiler at 9 bar and 88.7 m/s. Then, it enters the turbine through a constant 0.13 m diameter pipe. The exit pipe of the turbine is 0.3 m in diameter and T = 310ºC while P = 1.37 bar. If 2.5 kg/s water is fed and there is change in KE, prove that the fluid enters the turbine at 637.06 deg C.
In a steam power plant, steam enters the turbine at 2.5 MPa and 500 C. The condenser pressure is 15 KPa. The turbine and pump isentropic efficiencies are 94 % and 89 %, respectively. Determine the actual net work in kJ/kg. In solving, use two decimal places for the enthalpies/energies while four decimal places for the steam quality. For the final answer, use two decimal places
303 nt inces Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 13 kg/s. The properties of the steam are v=0.086442 m³/kg, h = 3446 kJ/kg, and 2 = 2437.7 kJ/kg. P = 4 MPa 7-500C VVER Steam P₂ = 30 kPa 4y=0.92 V₂50 m/s Determine the turbine inlet area. The turbine inlet area is m².