*10-28. Determine the force in member AD of the truss. The cross-sectional area of each member is shown in the fig- ure. Assume the members are pin connected at their ends. Take E = 29(10³) ksi. 5 k E 2 in? 3 in? 3 in? 3 ft 2 in? 2 in? 3 in2 2 in? 4 ft 2 in? 4 ft B 4 k

*10-28. Determine the force in member AD of the truss. The cross-sectional area of each member is shown in the fig- ure. Assume the members are pin connected at their ends. Take E = 29(10³) ksi. 5 k E 2 in? 3 in? 3 in? 3 ft 2 in? 2 in? 3 in2 2 in? 4 ft 2 in? 4 ft B 4 k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is horizontal. Forces are positive if in tension, negative if in compression. B Answer: AC = 3' AD = i i DE = i C 3' 600 lb D 3' E lb lb lb
Determine the force in members CD and CE of the truss shown below
The truss shown in figure below is made up of bars 2 mlong. Find the load carried by the members AB, GE, and CD.
Determine the forces in members DE, CE, and BC in the truss shown using the method of sections
*For the Howe bridge truss shown, d=11 ft,F1=3150 lb, F2=2150 lb, F3=2550 lb, and F4=4150 lb.* Pt A. Determine the forces in members CD, DH, and GH. Pt B. Determine the forces in members HI, BH, and BC.
For the Howe bridge truss shown, d=11 ft,F1=3250 lb, F2=2150 lb, F3=2450 lb, and F4=3950 lb.
From the figure shown, a truss is subjected to loads PI = 15 KN, P2=15 kN and P3-25 kN at joint C. D and E respectively. Use 5l = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy=248 MPa rx = 22.9 mm ry = 33.2 mm a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ S₁ CIVIL ENGINEERING- STEEL DESIGN ***
Determine the force in member AB , AC and BC of the truss only HANDWRITTEN answer needed ( NOT TYPED)
The truss ABC is constructed of three titanium (E Ti =17.4×10 3 ksi) members. A horizontal force of 1.8 kip and an unknown force P are applied to the truss at point B as shown. Member AB has a cross-sectional area of 0.1in 2 , member BC has a cross-sectional area of 0.0025ft 2 , and member AC has a cross-sectional area of 0.2 in2. b) Determine the magnitude of the force P that is required to displace the roller at point C to the right by .03 inches.
Determine the force in all members of the truss shown in the figure below. State whether the members are in tension or compression. The reactions at the supports have been calculated. Ax=0- A B A₂ = 9 KN 6 KN M H |+ 3 m G 8 KN 3 m D F 2 KN 3 m ** 3 m E [SM. JASM 4.5 m 3 m E₁ = 7 KN
Determine the forces in each members of the Howe roof truss shown in lbs. P1=774 kN and P2=1336 kN. Show solution, Free body diagrams and determine each member it is in tension or compression.
Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299