Answered: 10-2. Determine the reactions at the…

10-2. Determine the reactions at the supports A, B, and C, then draw the shear and moment diagrams. El is constant. 12 kip 3 kip/ft F6 ft- - 6 ft -12 ft- Prob. 10-2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Learning Goal: To be able to solve three-dimensional equilibrium problems using the equations of equilibrium. Part A As with two-dimensional problems, a free-body diagram is the first step in solving three-dimensional equilibrium problems. For the free-body diagram, it is important to identify the appropriate reaction forces and couple moments that act in three dimensions. At a support, a force arises when translation of the attached member is restricted and a couple moment arises when rotation is prevented.For a rigid body to be in equilibrium when subjected to a force system, both the resultant force and the resultant couple moment acting on the body must be zero. These two conditions are expressed as The J-shaped member shown in the figure(Figure 1) is supported by a cable DE and a single journal bearing with a square shaft at A. Determine the reaction forces Ay and Az at support A required to keep the system in equilibrium. The cylinder has a weight WB = 5.60 lb , and F = 1.50 Ib…
Choose the letter of the correct answer.
provide complete and neat solution
Using the virtual work method determine slope of the beam at "A". Beam is subjected to a uniformly Distributed Load “W" and a concentrated moment "WL^2" at “A" (Express the results in terms of W, L, and EI) w ikIft=constant)
Solve for the end moments using the 7-step matrix method of the following beams. 200KN |160KN 32KN/m 2m 2m 2m 4m A B
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
USE CONJUGATE BEAM METHOD IN SOLVING THE PROBLEM
Find the maximum angle of rotation for the shaft subjected to linearly %3D distributed torque. Tx) = kx,GJ constant. T(x)
Please help
Civil Engineering Finite Element Method Q1:Cosider the axially loaded nonprismatic member shown below. Using a quadratic isoparametric element (3 nodes), derive the stiffness matrix and the load vector due to self weight of the member. A1 nodel IA node 3 node2 A 21
the value of the integration constant C2. the value of the integration constant C4. the value of the deflection at point C.
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 5.0 m, b = 1.7 m, wA = 16 kN/m, and wB = 46 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.