10-1. The piping of Fig. 10-50 is all the same size and part of a larger water distribution system.Figure 10-50 Sketch for Problem 10-1.ToblemsUj23 - 20t (6m)U34- 15t (4.6m)H, = B0ft (24m)PumpPROBLEMS(a) Compute the pressure at points 2, 3, and 4 if the pressure at point 1 is 20 psig (138 kPagage). (b) Sketch the system characteristic for the complete run of pipe. Assume a flow rate of150 gpm (9.5 L/s).

Answered: Image /qna-images/answer/2831b997-45d7-466a-8b78-480e2648217e.jpg

Answered: 10-1. The piping of Fig. 10-50 is all…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressurized tank and piping system are shown in the figure. The tank pressure is maintained at 175 kPa. The line is made of 12 m of 1 std type M copper tubing and it conveys gasoline (octane). What is the expected flow rate through the line? All fittings are soldered (same as flanged) and regular. 4 m 175 kPa 1 m
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
Calculate using SI units a) the mass flow rate in pipe 1 and pipes 3
please only type answer
Q:/ Discuss the relation betwveen the head pressure and flow rate for the benefits of connecting the pumps in parallel ?
Please help, will give helpful ratings if correct!!!
For the hydraulic system of Figure 8, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3(b) The pipe inside diameter is 0.0254m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).
Draw and describe a simplified diagram of a section of an industrial sugar and alcohol piping system, which contains the following equipment: 1 Pump 1 Heat Trocador Elbows for changing the flow path Flux Valves The ultimate goal is to calculate system and pump pressure losses.
This is a practice problem for an upcoming test, but I'm not really sure which direction to solve it in. If I use a basic pressure equation do I have to do iterations? Cause we should be able to take a ratio of flow in both pipes. Any information on the direction of how to solve this problem will be extremely helpful, as well as solving it.
A duct system layout is shown in the figure below, it is supplied with air from a central air conditioning unit. The ducts require to be rectangular with a maximum height of 10in due to ceiling limitations. Maximum air duct velocities are: main = 1200fpm; branches = 800 fpm. Determine the sizes of the rectangular ducts and the static pressure at the AHU. Use Velocity reduction method. AHU- AIR HANDLING UNIT (CENTRAL AIRCON)
Is there a flaw in the pipeline design as shown in Flgure 4 ? (select one): (A) The strainer and foot valve should not be used as the combination may cause cavitation. (B) The foot valve should not be used as it may cause cavitation. (C) The pump should be placed at a higher elevation to prevent cavitation from occurring. (D) The gate valve should not be placed on the suction side of the pump as it may cause cavitation. (E) The intake is not placed deep enough below the water surface of the river as it may cause cavitation. (F) None Elevation 180 m- 450 All of Steel Pipe Diameter 250mm· Smooth Bend B Gate Valve- (wide open) River Elevation -Pump at Elevation 125 m 120 m Smooth Bend Sump -Strainer and foot valve at 115m Figure 4

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS